High-performance INOX cut
High-performance tungsten carbide burs, INOX cut, 14° Taper bur with radius end – Shape L
With the INOX cut, PFERD has developed innovative burs specifically for stainless steel (INOX). They achieve incredibly high stock removal on all austenitic steels, as well as rust- and acid-resistant steels. The INOX cut generates significantly less vibration in comparison to a double cut bur. 14° Taper bur with round radius end, shape L.Special featuresExcellent stock removal rate and impressive service life due to innovative tooth design.Creates high quality surface finish and the optimum material chip formation.Workpiece is protected through much lower thermal load.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.To ensure costeffective use of burrs, use a higher rotational speed and cutting speed. Use burrs with a shank diameter of 1/8" with drives with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsHard non-ferrous metalStainless steel (INOX)TitaniumTitanium alloysApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, INOX cut, Ball bur – Shape D
With the INOX cut, PFERD has developed innovative burs specifically for stainless steel (INOX). They achieve incredibly high stock removal on all austenitic steels, as well as rust- and acid-resistant steels. The INOX cut generates significantly less vibration in comparison to a double cut bur. Ball-shaped bur, shape D.Special featuresExcellent stock removal rate and impressive service life due to innovative tooth design.Creates high quality surface finish and the optimum material chip formation.Workpiece is protected through much lower thermal load.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.To ensure costeffective use of burrs, use a higher rotational speed and cutting speed. Use burrs with a shank diameter of 1/8" with drives with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsHard non-ferrous metalStainless steel (INOX)TitaniumTitanium alloysApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, INOX cut, Cylindrical bur with plain end (uncut) – Shape A
With the INOX cut, PFERD has developed innovative burs specifically for stainless steel (INOX). They achieve incredibly high stock removal on all austenitic steels, as well as rust- and acid-resistant steels. The INOX cut generates significantly less vibration in comparison to a double cut bur. Cylindrical burSpecial featuresExcellent stock removal rate and impressive service life due to innovative tooth design.Creates high quality surface finish and the optimum material chip formation.Workpiece is protected through much lower thermal load.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.To ensure costeffective use of burrs, use a higher rotational speed and cutting speed. Use burrs with a shank diameter of 1/8" with drives with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsHard non-ferrous metalStainless steel (INOX)TitaniumTitanium alloysApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, INOX cut, Cylindrical bur with radius end – Shape C
With the INOX cut, PFERD has developed innovative burs specifically for stainless steel (INOX). They achieve incredibly high stock removal on all austenitic steels, as well as rust- and acid-resistant steels. The INOX cut generates significantly less vibration in comparison to a double cut bur. Cylindrical bur with rounded radius end, shape C.Special featuresExcellent stock removal rate and impressive service life due to innovative tooth design.Creates high quality surface finish and the optimum material chip formation.Workpiece is protected through much lower thermal load.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.To ensure costeffective use of burrs, use a higher rotational speed and cutting speed. Use burrs with a shank diameter of 1/8" with drives with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsHard non-ferrous metalStainless steel (INOX)TitaniumTitanium alloysApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, INOX cut, Tree bur with pointed end – Shape G
With the INOX cut, PFERD has developed innovative burs specifically for stainless steel (INOX). They achieve incredibly high stock removal on all austenitic steels, as well as rust- and acid-resistant steels. The INOX cut generates significantly less vibration in comparison to a double cut bur. Tree bur with pointed end, shape G.Special featuresExcellent stock removal rate and impressive service life due to innovative tooth design.Creates high quality surface finish and the optimum material chip formation.Workpiece is protected through much lower thermal load.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.To ensure costeffective use of burrs, use a higher rotational speed and cutting speed. Use burrs with a shank diameter of 1/8" with drives with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsHard non-ferrous metalStainless steel (INOX)TitaniumTitanium alloysApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, INOX cut, Tree bur with radius end – Shape F
With the INOX cut, PFERD has developed innovative burs specifically for stainless steel (INOX). They achieve incredibly high stock removal on all austenitic steels, as well as rust- and acid-resistant steels. The INOX cut generates significantly less vibration in comparison to a double cut bur. Tree bur with radius end, shape F.Special featuresExcellent stock removal rate and impressive service life due to innovative tooth design.Creates high quality surface finish and the optimum material chip formation.Workpiece is protected through much lower thermal load.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.To ensure costeffective use of burrs, use a higher rotational speed and cutting speed. Use burrs with a shank diameter of 1/8" with drives with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsHard non-ferrous metalStainless steel (INOX)TitaniumTitanium alloysApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder