High-performance EDGE cut
High-performance tungsten carbide burs, EDGE cut, Concave radius bur EDGE R-1/8
EDGE cut tungsten carbide burs have been specifically developed for precise work on edges. The special design allows the bur to run directly along edges without damaging the workpiece. Exact edges can be created in a single step - with either defined chamfers of 30° or 45°, or to a defined radius of 1/8". Rounding edges is a precautionary measure against corrosion according to: ISO 129443, ISO 85013, SOLAS XII/6.3 (Ref. T4/3.01 MSC.1/Circ.1198). Concave radius bur for producing precise rounded edges. Cannot be re-sharpened. Designed for producing and finishing edges with an 1/8" outer radius." The EDGE Cutting System includes EDGE cut burs and a special guide sleeve that can be mounted into a conventional power tool collet to ensure optimal guidance during light deburring work.Special featuresImproved guidance.Can be used with any conventional straight grinder.Bur is interchangeable.Special design allows for precise handling.Safe and comfortable use.Exact edge shapes can be created in a single step.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs counterrotationally for quick stock removal. For a fine surface finish, run the bur back over the edges in the same direction of rotation.If possible, use burs with the EDGE cut with the PFERD compressed-air straight grinder PG 3/210 with the matching guide sleeve EFH PG 3/210.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BronzeCast ironCast steelCobalt-based alloysCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hard non-ferrous metalSteelSteel, cast steelSteels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsChamferingDeburringMillingRoundingWorking on edgesWorking on edges (chamfering, rounding)Compatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, EDGE cut, Cone counterbore EDGE 30°
EDGE cut tungsten carbide burs have been specifically developed for precise work on edges. The special design allows the bur to run directly along edges without damaging the workpiece. Exact edges can be created in a single step - with either defined chamfers of 30° or 45°, or to a defined radius of 1/8". Rounding edges is a precautionary measure against corrosion according to: ISO 129443, ISO 85013, SOLAS XII/6.3 (Ref. T4/3.01 MSC.1/Circ.1198). Cone counterbore bur for producing precisely defined chamfers. Designed for counterboring and chamfering of defined 30° chamfer angles.Special featuresSpecial design allows for precise handling.Safe and comfortable use.Exact edge shapes can be created in a single step.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs counterrotationally for quick stock removal. For a fine surface finish, run the bur back over the edges in the same direction of rotation.If possible, use burs with the EDGE cut with the PFERD compressed-air straight grinder PG 3/210 with the matching guide sleeve EFH PG 3/210.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)PlasticsSteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)ZincApplicationsChamferingDeburringMillingWorking on edgesWorking on edges (chamfering, rounding)Compatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, EDGE cut, Cone counterbore EDGE 45°
EDGE cut tungsten carbide burs have been specifically developed for precise work on edges. The special design allows the bur to run directly along edges without damaging the workpiece. Exact edges can be created in a single step - with either defined chamfers of 30° or 45°, or to a defined radius of 1/8". Rounding edges is a precautionary measure against corrosion according to: ISO 129443, ISO 85013, SOLAS XII/6.3 (Ref. T4/3.01 MSC.1/Circ.1198). Cone counterbore bur for producing precisely defined chamfers. Designed for counterboring and chamfering of defined 45° chamfer angles.Special featuresSpecial design allows for precise handling.Safe and comfortable use.Exact edge shapes can be created in a single step.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Improved guidance.Can be used with any conventional straight grinder.Bur is interchangeable.Recommendations for useUse the burs counterrotationally for quick stock removal. For a fine surface finish, run the bur back over the edges in the same direction of rotation.If possible, use burs with the EDGE cut with the PFERD compressed-air straight grinder PG 3/210 with the matching guide sleeve EFH PG 3/210.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.Workpiece materialsAluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)PlasticsSoft aluminium alloysSteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)ZincApplicationsChamferingDeburringMillingWorking on edgesWorking on edges (chamfering, rounding)RoundingCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder