High-performance ALU cut
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, 14° Taper bur with radius end – Shape L
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. 14° Taper bur with round radius end, shape L.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Ball bur – Shape D
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Ball-shaped bur, shape D.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/8" shank diameter, use power tools with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Cylindrical bur with end cut – Shape B
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Cylindrical bur with end cut, shape B.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/8" shank diameter, use power tools with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Cylindrical bur with plain end (uncut) – Shape A
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Cylindrical burSpecial featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Cylindrical bur with radius end – Shape C
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Cylindrical bur with rounded radius end, shape C.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/8" shank diameter, use power tools with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Flame bur – Shape H
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Flame bur, shape H.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Oval bur – Shape E
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Tree bur with pointed end – Shape G
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Tree bur with pointed end, shape G.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Tree bur with radius end – Shape F
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Tree bur with radius end, shape F.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/8" shank diameter, use power tools with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder