High-performance ALU cut with HICOAT® coating HC-NFE
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, 14° Taper bur with radius end – Shape L
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. 14° Taper bur with round radius end, shape L.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, Ball bur – Shape D
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. Ball-shaped bur, shape D.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, Cylindrical bur with end cut – Shape B
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. Cylindrical bur with end cut, shape B.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, Cylindrical bur with radius end – Shape C
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. Cylindrical bur with rounded radius end, shape C.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, Tree bur with radius end – Shape F
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. Tree bur with radius end, shape F.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder