Sanding Abrasives
COMBIDISC® Abrasive Disc Set, Type CDR, Prep to Paint
Prep-to-paint set includes a selection of coated and non-woven abrasives for removal of surface imperfections such as rust, loose paint or cold drawn mill scale. Selected discs leave the proper surface finish for excellent wet and dry paint and coating adhesion.
COMBIDISC® abrasive discs
COMBIDISC Abrasive DiscFor aggressive grinding with maximum stock removal rate on hard materials that do not conduct heat well. Consistently high performance due to self-sharpening ceramic oxide grain. Active grinding additives in the coating substantially improve the stock removal rate, prevent loading, and result in cooler grinding. The CD clamping system has a threaded connection with female thread (metal/plastic). Also compatible with the following commonly used systems: PSG, Power Lock Type II "turn on", SocAtt, Turn-On.Special featuresReduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsDeburringStep-by-step fine grindingLevelingRougheningSharpeningSurface workWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)TitaniumAluminumAnnealed cast ironBronzeCobalt-based alloysGrey/nodular cast iron (GG/GJL, GGG/GJS)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse COMBIDISC® grinding discs with arbors or abrasive disc holders on flexible shaft drives with angle handpieces, compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationDia. External2 inDrive typeAngle grinderGrit24Pack qty100
COMBIDISC® CONTOUR Abrasive Disc
COMBIDISC CONTOUR Abrasive DiscVery flexible and adaptable due to scalloped-edge outer contour shape. Helps prevent cutting into the workpiece. The CD clamping system has a threaded connection with female thread (metal/plastic). Also compatible with the following commonly used systems: PSG, Power Lock Type II "turn on", SocAtt, Turn-On.Special featuresReduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsDeburringStep-by-step fine grindingLevelingRougheningSharpeningSurface workWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAnnealed cast ironBrassBronzeCast steelCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useUse COMBIDISC® grinding discs with arbors or abrasive disc holders on flexible shaft drives with angle handpieces, compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.Use a 1" - 2" diameter abrasive disc holder.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationDia. External2 3/8 inDrive typeAngle grinderGrit60 CONTOURPack qty50
COMBIDISC® Felt Disc
COMBIDISC Felt DiscDesigned for polishing with polishing paste bars, grinding pastes, or diamond polishing pastes in face-down grinding on small and medium-sized surfaces. The CDR clamping system has a threaded connection with male thread (plastic). Also compatible with the following commonly used systems: Roloc™, Lockit, Speed Lok TR, Power Lock Type III, Fastlock-System B, Roll-On.Special featuresReduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse COMBIDISC® felt discs with a abrasive disc holders on flexible shaft drives with angle handpieces, or small compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.When applying a different polishing paste, use a new unused felt disc.For the best performance, use with a recommended peripheral speed of 1,000-2,000 SFPM. This provides an ideal compromise between polishing performance, thermal load on the workpiece and tool wear.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.Technical informationDia. External2 inDrive typeAngle grinderPack qty10
COMBIDISC® mini fibre discs
COMBIDISC Abrasive DiscDesigned for surface and edge grinding. The fiber backing strengthens the abrasive disc and improves stock removal. Each VICTOGRAIN abrasive grain triangle is firmly fixed on one of its sides to the backing material. Due to the slim design, VICTOGRAIN offers an extremely large chip space for maximum cutting efficiency. The structure of the triangular VICTOGRAIN is specially engineered to maximize results. The very fine crystalline structure ensures optimal wear characteristics as sharp cutting edges are always exposed, with the minimum amount of abrasive breaking off from the triangle. By combining all these properties together, users benefit from optimal, consistent performance, cool grinding and an extremely long service life with uniform workpiece surface roughness. The CD clamping system has a threaded connection with female thread (metal/plastic). Also compatible with the following commonly used systems: PSG, Power Lock Type II "turn on", SocAtt, Turn-On.Special featuresVICTOGRAIN abrasive grain allows for high productivity due to long service life, very high stock removal rate, less heat build-up in the workpiece, and a lower power output required for the power tool.Reduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsDeburringLevelingSurface workWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)SteelSteel, cast steelSteels up to 370 HV (< 38 HRC)Cast steelHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse COMBIDISC® mini fiber discs with abrasive disc holders on flexible shaft drives with angle handpieces, or small compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationDia. External2 inDrive typeAngle grinderGrit36Pack qty100
COMBIDISC® Mini Flap Disc
COMBIDISC Mini Flap DiscFor universal coarse grinding work with high stock removal rates. Ideal for dressing weld seams in hard-to-reach places. Longer service life and higher stock removal rate when compared to abrasive discs. The CD clamping system has a threaded connection with female thread (metal/plastic). Also compatible with the following commonly used systems: PSG, Power Lock Type II "turn on", SocAtt, Turn-On.Special featuresReduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsDeburringStep-by-step fine grindingLevelingRougheningSharpeningSurface workWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAnnealed cast ironBrassBronzeCast steelCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useUse COMBIDISC® Mini-POLIFAN discs with arbors on flexible shaft drives with angle handpieces, or small compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationDia. External2 inDrive typeAngle grinderGrit40Pack qty10
COMBIDISC® non-woven finishing discs, soft type
COMBIDISC Non-Woven Abrasive DiscDesigned for very fine grinding on small and medium-sized surfaces and contours, and for cleaning metal and painted surfaces. Achieve matte and satin-finished surfaces. Highly open structure. The CD clamping system has a threaded connection with female thread (metal/plastic). Also compatible with the following commonly used systems: PSG, Power Lock Type II "turn on", SocAtt, Turn-On.Special featuresReduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsCleaningDeburringStep-by-step fine grindingRougheningStructuring (matt finishing, brush matting and satin finishing)Surface workWork on weld seamsMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse COMBIDISC® non-woven discs with abrasive disc holders on flexible shaft drives with angle handpieces, or small compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.Adding oil or water during grinding results in a finer finish, cooler grinding, and longer service life.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.Technical informationVersionmediumDia. External2 inDrive typeAngle grinderGrit100Pack qty50
COMBIDISC® non-woven surface-conditioning discs, hard type
COMBIDISC Non-Woven Abrasive DiscDesigned for universal work on small and medium-sized metal surfaces, e.g. removing rough grinding traces, removing oxidation, and light deburring work. Achieve matte and satin-finished surfaces. POLIVLIES® grit size 100 G = coarse (yellow-brown) The CD clamping system has a threaded connection with female thread (metal/plastic). Also compatible with the following commonly used systems: PSG, Power Lock Type II "turn on", SocAtt, Turn-On.Special featuresReduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsCleaningDeburringStep-by-step fine grindingRougheningStructuring (matt finishing, brush matting and satin finishing)Surface workWork on weld seamsMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse COMBIDISC® non-woven discs with abrasive disc holders on flexible shaft drives with angle handpieces, or small compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.Adding oil or water during grinding results in a finer finish, cooler grinding, and longer service life.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.Technical informationVersioncoarse, yellow-brownDia. External2 inDrive typeAngle grinderGrit100 GPack qty50
COMBIDISC® POLICLEAN® PLUS Disc
COMBIDISC POLICLEAN PLUS DiscFor coarse cleaning work such as removing paint, scale, heat discoloration, rust and adhesive residues in face-down grinding. The CD clamping system has a threaded connection with female thread (metal/plastic). Also compatible with the following commonly used systems: PSG, Power Lock Type II "turn on", SocAtt, Turn-On.Special featuresThe PLUS version (blue) has a considerably higher stock removal rate and a very good service life, and it is very aggressive.Reduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsCleaningDeburringRougheningSurface workMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumAnnealed cast ironBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse with hard or medium-hard COMBIDISC® abrasive disc holders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.Technical informationVersionPCLR PLUSDia. External2 inDrive typeAngle grinderPack qty10
COMBIDISC® RS Abrasive Disc
COMBIDISC RS Abrasive DiscFor aggressive grinding with maximum stock removal rate on hard materials that do not conduct heat well. Consistently high performance due to self-sharpening ceramic oxide grain. Active grinding additives in the coating substantially improve the stock removal rate, prevent loading, and result in cooler grinding. RS type COMBIDISC® abrasive discs are ideal for weld dressing of backwards repair welds, e.g. in cases, slots and grooves on engines and for processing welded-on combustor plates. Unlike on conventional abrasive discs, the abrasive coating is on the underside of the tool, which allows backwards working.Special featuresIdeal for use in extremely difficult-to-reach areas.Convenient and safe backward working.Reduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsDeburringStep-by-step fine grindingLevelingRougheningSharpeningSurface workWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)TitaniumAluminumAnnealed cast ironBronzeCobalt-based alloysGrey/nodular cast iron (GG/GJL, GGG/GJS)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse COMBIDISC® mini fiber discs with abrasive disc holders on flexible shaft drives with angle handpieces, or small compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.Move the disc to the appropriate location on the workpiece. To grind, do not push it onto the surface, pull it toward yourself.To ensure get the most out of the disc's grinding surface, use the appropriate abrasive disc holder.Always use the RS abrasive discs at the specified optimum rotational speed and not the maximum permitted rotational speeds of the backing pad EDP 42454.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationDia. External1 1/2 inDrive typeAngle grinderGrit50Pack qty100
COMBIDISC® Unitized Disc
COMBIDISC Unitized DiscFor achieving a very fine, uniform surface finish which, depending on requirements, is a sufficient preparation for high-gloss polishing. Ideal for small and medium-sized surfaces on stainless steel (INOX) components. The CD clamping system has a threaded connection with female thread (metal/plastic). Also compatible with the following commonly used systems: PSG, Power Lock Type II "turn on", SocAtt, Turn-On.Special featuresReduced down time due to quick changes.Convenient to use due to simple handling and low-vibration working.No operational disruptions caused by sticking, slipping, or disengaging.ApplicationsCleaningDeburringStep-by-step fine grindingRougheningStructuring (matt finishing, brush matting and satin finishing)Surface workWork on weld seamsMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse COMBIDISC® non-woven discs with abrasive disc holders on flexible shaft drives with angle handpieces, or small compressed-air or electric angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyThe maximum permitted peripheral speed is 9,800 SFPM.Technical informationVersionW (soft)Dia. External2 inWidth1/4 inDrive typeAngle grinderGritG (coarse)Max. RPM19100Pack qty25
Diamond Polishing Paste, Cap Color Yellow
Diamond Polishing Paste, Cap Color YellowDiamond polishing pastes allow for quick and efficient work, particularly in tool and die making. Diamond polishing pastes are used for work on hard materials, such as tungsten carbide and hardened steels. They are used in combination with felt polishing elements. Diamond polishing pastes can be diluted and dissolved with water and alcohol. ECO diamond polishing pastes are an affordable option. Grit size according to ISO 6344 = P 14000Special featuresHigh productivity.Quick results.Specialized selection of grit sizes.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useWhen using diamond polishing pastes, use the most coarse paste first.If extensive surface improvements are needed, use several grit sizes one after another, each finer than the previous, cleaning well between pastes.When changing grit size, make sure that a new, clean polishing product (e.g. felt point or felt wheel) is used.Technical informationDrive typeManual applicationGrit1Pack qty1
ECO AC Paper Backed Abrasive Sheet
ECO AC Paper Backed Abrasive SheetThe stearate coating is a non-stick coating (AC) that prevents the abrasive sheets from clogging. The ECO AC version with aluminum oxide A is a low-cost alternative for general grinding work in industry and professional trades. The paper-backed abrasive sheets comply with ISO 21948. Grit size 60 comes in packs of 50.Special featuresHigh abrasive performance through very good grain adhesion.The non-stick coating (AC) prevents loading with low wear.High tear strength with optimum quality.ApplicationsCleaningStep-by-step fine grindingRougheningSurface workMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumAnnealed cast ironBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useTear to the necessary size as needed.Technical informationWidth9 inDrive typeManual applicationGrit60Pack qty50
ECO W Paper Backed Abrasive Sheet
ECO W Paper Backed Abrasive SheetThe ECO W version with silicon carbide (SiC) is a low-cost alternative for use on paint and glass. Particularly suitable for all wet grinding work on conventional painted constructions. The paper-backed abrasive sheets comply with ISO 21948. Grit size 60 comes in packs of 50.Special featuresGood grain adhesion on very flexible and light paper.Maximum abrasive performance.Can be used for wet and dry grinding.High tear strength with optimum quality.ApplicationsCleaningStep-by-step fine grindingRougheningSurface workMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumAnnealed cast ironBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useTear to the necessary size as needed.Technical informationWidth3/4 inDrive typeManual applicationGrit60Pack qty50
Felt Flap Disc
Felt Flap DiscFelt flap discs are used for pre-polishing and high-gloss polishing on medium-sized to large components. Due to their hardness and flexibility, felt flap discs are used when the exact form of geometric shapes has to be maintained. As a general rule, diamond polishing pastes and polishing paste bars are used for this.Special featuresConforms to contours due to high flexibility.Can be freely shaped, meaning they can be used on complicated geometries.Low thermal load on the workpiece.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse the soft type for buffing and processing workpieces with lots of contours. If a very fine finish is desired, the hard and soft types can be used successively.Technical informationVersionW (soft)Dia. External4 1/2 inWidth7/8 inDrive typeAngle grinderMax. RPM8350Pack qty5
Felt Point
Felt PointDue to their hardness and flexibility, felt points are used when the exact form of geometric shapes has to be maintained. The cylindrical shape is mainly used peripherally.Special featuresCan be freely shaped, meaning they can be used on complicated geometries.Precise retention of geometric shapes due to the hardness of these products.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useFor the best performance, use with a recommended peripheral speed of 1,000-2,000 SFPM. This provides an ideal compromise between stock removal rate, surface quality, thermal load on the workpiece and tool wear.Use diamond polishing pastes and polishing paste bars.When applying a different polishing paste, use a new unused polishing product.SafetyFor safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationShapeCylindersVersionM (medium)Dia. External1/4 inWidth3/8 inDia. shank1/8 InchDrive typeFlexible shaft driveMax. RPM79500Pack qty10
Felt Polishing Belt
Felt Polishing BeltDesigned for polishing with polishing paste bars and grinding pastes on tubular constructions and railings. Short belts are compatible with commonly available belt grinders.Special featuresHigh tear strength with optimum flexibility.Cost-effective due to high abrasive performance and durability.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumAnnealed cast ironBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useFor the polishing process, apply pre-polishing and high-gloss polishing successively.When changing the polishing paste, also replace the polishing belt so no contaminants are included from previous step.For best performance, use at a recommended peripheral speed of 1,000-3,000 SFPM.SafetyFollow all safety instructions for abrasive belt use.Technical informationWidth4 inDrive typeDrum grindersPack qty5
Felt Wheel
Felt WheelFelt wheels are mainly used peripherally for high-gloss polishing.Special featuresPrecise retention of geometric shapes due to the hardness of these products.Can be freely shaped, meaning they can be used on complicated geometries.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse diamond polishing pastes and polishing paste bars.When applying a different polishing paste, use a new unused polishing product.SafetyFor safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationShapeDiscVersionM (medium)Dia. External1 3/4 inWidth3/8 inDrive typeFlexible shaft driveMax. RPM13500Pack qty5
Fiber disc storage device
Fiber disc storage deviceFibre disc storage device made from impact-resistant plastic. Device helps maintain fiber disc shape and prevents curling. The storage device can be stood upright, as well as mounted to walls. Designed for 4" to 9" fiber disc diameters.Special featuresExcellent storage for fibre grinding discs.With quick adjustment device and attachment holes on the base.Technical informationDrive typeAngle grinderPack qty1
Fiber Disc
Fiber DiscPFERD fiber discs are manufactured in accordance with ISO 16057 in shape A2 version F under the designation "vulcanized fiber disc". For universal grinding work from coarse to fine grinding in industry and professional trades.Special featuresHigh productivity due to long service life and very high stock removal rate.Consistent surface finish resulting from high-quality abrasives.Conforms to contours due to high flexibility.ApplicationsDeburringStep-by-step fine grindingLevelingSurface workWork on weld seamsWorking on edgesMaterials that can be workedSteel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)AluminumAnnealed cast ironBrassCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useUse fiber disc in accordance with ISO 15636 with backing pad on commercially available angle grinders.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyThe maximum permitted peripheral speed is 15,800 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationDia. External7 inDrive typeAngle grinderGrit16Max. RPM8500Pack qty25
Flap Disc, PVL-R, POLIVLIES® CURVE
Flap Disc, PVL-R, POLIVLIES CURVEEngineered for maximum operational efficiency, the PFERD PVL-R POLIVLIES® CURVE Flap Disc delivers superior surface conditioning and material removal performance. Featuring a coarse-grade aluminum oxide abrasive, this disc is optimized for aggressive stock removal while maintaining consistent surface integrity across ferrous and non-ferrous metals. Constructed with a high-performance abrasive non-woven material, the flap design continuously exposes fresh, sharp abrasive grains during use, ensuring uniform surface quality and extended service life. The CURVE profile allows for edge grinding and contour following, making it ideal for applications requiring precision on irregular geometries and hard-to-reach surfaces.Special featuresCost-effective due to high abrasive performance and durability.Creates a consistently high surface quality throughout the entire service life, as new sharp abrasive material is constantly exposed.Conforms to contours due to high flexibility.ApplicationsCleaningDeburringStep-by-step fine grindingRougheningStructuring (matt finishing, brush matting and satin finishing)Surface workWork on weld seamsMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useFor the best performance, use with a recommended peripheral speed of 6,000-7,000 SFPM.SafetyFor safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Technical informationVersioncoarseDia. External4 1/2 inDrive typeAngle grinderGrit100Max. RPM13300Pack qty5
Flap Disc, Z PSF EXTRA STEELOX, Flat, Zirconia
Choose the Universal Line PSF for processing the most common materials. These robust products achieve good results with increased economic efficiency. POLIFAN flap disc for steel and stainless steel (INOX). Aggressive stock removal rate and good service life.
Flap Disc, Z SGP CURVE STEELOX, Zirconia
Special Line SGP includes products engineered for specific tasks that offer the user key advantages over conventional products. This quality line also includes products that, due to their particularly high performance, offer ultimate economic efficiency. The patented flap disc POLIFAN-CURVE has been specially developed for work on fillet welds. It is the only flap disc in the world featuring a radial configuration of flaps allowing for grinding with all surfaces of the disc. PFERD’s POLIFAN CURVE is patented in many countries across the globe. High-performance flap disc for maximum stock removal on steel and stainless steel (INOX).
Flap Drum
Flap DrumDesigned for universal work on medium-sized and large metal surfaces, e.g. fine grinding work on large radii in container, kitchen, and appliance construction, and achieving uniform finishes (grinding patterns) on large surfaces and contours in manual applications. Designed for all conventional keyway systems.Special featuresConforms to contours due to high flexibility.Consistently high stock removal rate throughout the entire service life as new, aggressive abrasive is constantly exposed.ApplicationsDeburringStep-by-step fine grindingLevelingStructuring (matt finishing, brush matting and satin finishing)Surface workWork on weld seamsMaterials that can be workedSteel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)AluminumAnnealed cast ironBrassCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useFlap wheel wear and the thermal load on the workpiece are reduced by decreasing the contact pressure and peripheral speed, and by adding grinding oil.Stock removal rate should be increased by using a coarser grit, not by increasing the contact pressure. This avoids unnecessary flap wheel wear and prevents the thermal load of the workpiece.Increasing the speed results in a slightly finer surface quality. An increase in contact pressure results in a slightly coarser surface. The softer the workpiece material, the coarser the resulting surface (when using the same grit size).For the best performance, use with a recommended peripheral speed of 3,000-6,000 SFPM. This provides an ideal compromise between stock removal rate, surface quality, thermal load on the workpiece and tool wear.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.For the best results, use a power tool with 1,000–1,500 watts.SafetyFor safety reasons, the maximum permitted rotational speed indicated must never be exceeded.The contact pressure has to be reduced significantly when the optimum rotational speed is exceeded.The maximum permitted peripheral speed is 6,300 SFPM.Technical informationDia. External4 inWidth4 inDrive typeDrum grindersGrit40Max. RPM6100Pack qty1