Milling, holemaking and deburring products
4-1/2"/5" ALUMASTER Carbide Insert Set - 10 Inserts
Specially developed cutting inserts from PFERD are durable and achieve a high stock removal rate. Cutting insert set for ALUMASTER High Speed Disc.
4-1/2"/5" ALUMASTER Service Set - TORX Key, 2 Screws, 2 Inserts
These service sets from PFERD allow the most common parts to be replaced in case of loss or damage. PFERD offers a replacement parts set for hole saw arbors and a service set for the ALUMASTER High Speed Disc. For swapping individual cutting inserts on the ALUMASTER High Speed Disc. This set contains two cutting inserts, two screws, and a hexalobular socket wrench.
High-performance tungsten carbide bur set, ALU cut
The 5-piece ALU cut bur set contains five tungsten carbide burs for processing aluminum. These burs are the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, CAST cut
This set contains five tungsten carbide burs for processing cast iron. These burs are the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.Special featuresUp to 100% higher stock removal rate on cast iron than conventional double cut burs, due to an innovative tooth design.Significantly increased aggressiveness, creates large chips, and has very good chip removal due to its innovative tooth design.Comfortable to use due to reduced vibration and less noise.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)Cast ironGrey/nodular cast iron (GG/GJL, GGG/GJS)White annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, Diamond cut
Diamond cut burs are designed for machining stainless steel (INOX), steel, and high-temperature-resistant materials such as nickel-based and cobalt-based alloys. They have high stock removal with short chips, and achieve a good surface finish. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. This set contains five tungsten carbide burs in the shapes and dimensions most commonly used in the workshop. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.Special featuresGood stock removal rate due to high quality tungsten carbide, bur shape, cut, and optional coating.Durable.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.High surface quality.Recommendations for useThe smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)Case-hardened steelsCast ironCast steelCobalt-based alloysGrey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHardened, heat-treated steels over 370 HV (38 HRC)High-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, Double cut
Double cut burs are cross cut and ideal for machining cast iron, steel, stainless steel (INOX), nickel-based alloys, and titanium alloys. These burs have a high stock removal rate. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. This set contains twelve small tungsten carbide burs in the shapes and dimensions most commonly used in the workshop. The sturdy plastic box protects the burs against dirt and damage.Special featuresGood stock removal rate due to high quality tungsten carbide, bur shape, cut, and optional coating.Durable.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.High surface quality.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCobalt-based alloysGrey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHardened, heat-treated steels over 370 HV (38 HRC)High-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel materials with a hardness > 54 HRCSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, INOX cut
This set contains five tungsten carbide burs for processing stainless steel (INOX). These burs are the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and. The box also has five unused slots for additional burs.Special featuresExcellent stock removal rate and impressive service life due to innovative tooth design.Creates high quality surface finish and the optimum material chip formation.Workpiece is protected through much lower thermal load.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsHard non-ferrous metalStainless steel (INOX)TitaniumTitanium alloysApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, MICRO cut
MICRO cut tungsten carbide burs are specifically designed for finishing and are used in areas where mounted points are often used. They offer a higher stock removal rate and produce a high surface quality, particularly when compared to conventional double cut burs. MICRO cut burs also operate with low vibration and little noise, they maintain their geometry over their entire service life, and they work in both manual and machine applications. MICRO cut burs can machine almost all materials up to a hardness of 940 HV (68 HRC). This set contains three small tungsten carbide burs for finishing work in the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage.Special featuresHigh surface quality.In comparison to abrasive mounted points, there is no change in geometry due to wear and tear.Work on almost all materials up to 940 HV (68 HRC).The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useIdeal for finishing, very fine cleaning work, corrections in tool and mold construction, and for sharpening cutting tools.Use the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BronzeCase-hardened steelsCast ironCast steelCobalt-based alloysGrey/nodular cast iron (GG/GJL, GGG/GJS)Hard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, mixed cuts
This set contains five tungsten carbide burs with different high-performance cuts for use on the most important materials such as steel, stainless steel (INOX), aluminum, and cast iron. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.Special featuresUp to 100% higher stock removal rate on cast iron than conventional double cut burs, due to an innovative tooth design.Significantly increased aggressiveness, creates large chips, and has very good chip removal due to its innovative tooth design.Comfortable to use due to reduced vibration and less noise.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Workpiece materialsAluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)PlasticsSoft aluminium alloysSoft non-ferrous metalStainless steel (INOX)SteelSteel materials with a hardness > 54 HRCSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysTool steelsTough aluminium alloysWhite annealed cast iron (GTW, GJMW)ZincApplicationsCutting out holesDeburringLevelingMillingMilling outWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, OMNI double cut
This set contains eight tungsten carbide burs in the shapes and dimensions most commonly used in the workshop. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has two unused slots for additional burs.Special featuresSignificantly better stock removal rate than conventional double cut burs.Saves time and money with very high stock removal rate on key materials.Comfortable working due to reduced vibration and noise.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)ZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, Single cut
Single cut burs are ideal for machining cast iron, steel, stainless steel (INOX), nickel-based alloys, and titanium alloys. These burs have a high stock removal rate and achieve a good surface finish quality. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. This set contains twelve small tungsten carbide burs in the shapes and dimensions most commonly used in the workshop. The sturdy plastic box protects the burs against dirt and damage.Special featuresGood stock removal rate due to high quality tungsten carbide, bur shape, cut, and optional coating.Durable.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.High surface quality.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)Case-hardened steelsCast ironCast steelCobalt-based alloysGrey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHardened, heat-treated steels over 370 HV (38 HRC)High-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, STEEL cut
This set contains five tungsten carbide burs for processing steel and cast steel. These burs are the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.Special featuresUp to 50% higher stock removal rate on steel and cast steel in comparison to conventional double cut burs.Significantly increased aggressiveness, creates large chips, and has very good chip removal due to its innovative tooth design.Workpieces are protected due to significantly lower thermal load.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.Safety notesVery high speeds can cause discoloration on the shank. This does not constitute a safety risk.Workpiece materialsCase-hardened steelsCast steelHardened, heat-treated steels over 370 HV (38 HRC)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tool steelsApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide bur set, TOUGH cut
The TOUGH cut has been specially designed for tough operating conditions such as in shipyards, foundries and steel construction. It is also ideal for all demanding production environments where frequent tooth breakages and other damage to conventional burs occur. This set contains five tungsten carbide burs for tough applications in the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused holes for additional burs.Special featuresInnovative quick-mounting system guarantees convenient handling and cool grindingMinimized tooth chipping/breakage, splintering, and bur failures due to very robust, high-performance cut.Can also be used at a lower rotational speed.Due to their extreme impact resistance, they are an ideal option when an extended-shank bur is needed.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useObserve the recommended rotational speed.The TOUGH cut can be used on materials up to 580 HV (54 HRC). For hard materials, it is recommended to test the bur on the same material before using on the actual workpiece.TOUGH cut carbide burs are also designed for high-impact applications when using shank extensions, for applications with a high surface contact angle, for work on narrow contours, and for applications where slower rotational speeds are used.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)Case-hardened steelsCast ironCast steelGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)SteelSteel materials with a hardness > 54 HRCSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, 14° Taper bur with radius end – Shape L
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. 14° Taper bur with round radius end, shape L.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Ball bur – Shape D
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Ball-shaped bur, shape D.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/8" shank diameter, use power tools with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Cylindrical bur with end cut – Shape B
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Cylindrical bur with end cut, shape B.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/8" shank diameter, use power tools with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Cylindrical bur with plain end (uncut) – Shape A
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Cylindrical burSpecial featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Cylindrical bur with radius end – Shape C
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Cylindrical bur with rounded radius end, shape C.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/8" shank diameter, use power tools with a power output of 75 to 300 watts.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, Flame bur – Shape H
PFERD has developed the ALU cut specifically for stock removal on aluminum. This cut achieves a high stock removal rate. Flame bur, shape H.Special featuresExtremely high stock removal rate.Creates large chips.Reduced material adhesion.Long service life and smooth running.Can be used with peripheral speeds of up to 3,600 SFPM.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, 14° Taper bur with radius end – Shape L
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. 14° Taper bur with round radius end, shape L.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, Ball bur – Shape D
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. Ball-shaped bur, shape D.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, Cylindrical bur with end cut – Shape B
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. Cylindrical bur with end cut, shape B.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, Cylindrical bur with radius end – Shape C
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. Cylindrical bur with rounded radius end, shape C.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
High-performance tungsten carbide burs, ALU/Non-Ferrous cut, HI-COAT NFE, Tree bur with radius end – Shape F
The PFERD HICOAT® coating HC-NFE prevents chips from sticking during work on soft aluminum alloys. This increases the bur service life and improves the surface quality of the workpiece. Tree bur with radius end, shape F.Special featuresUsed for removing material in long chips. Coating creates barrier between bur and workpiece which prevents loading of non-ferrous metals.Maximum stock removal rate.Effective chip removal due to improved anti-adhesion properties.Lower thermal loads.Increased service life.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Recommendations for useUse the burs on powerful power tools with elastically mounted spindles to avoid unwanted vibration.Observe the recommended rotational speed.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysSoft non-ferrous metalThermoplasticsTough aluminium alloysZincApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder