Milling, holemaking and deburring products
HSS hole saws thread version 5/8-18 UNF
Hole saws are made from tough, shatter-proof, sturdy HSS bi-metal. The saw teeth are made from high-quality M42 material. They are used for cutting out holes. The arbor with a 5/18-18 thread is part number 29034.Special featuresCost-effective sawing of round cut-outs.Alternating tooth pitch prevents chattering during sawing.High concentricity.Good chip removal.The hole saw is conveniently centered and guided via the replaceable bi-metal pilot drill.Hole saw arbor comes with an ejection spring for improved ejection of the cut material.Recommendations for useObserve the recommended rotational speed.Clamp the pilot drill in the hole saw arbor and make sure that it projects at least 1/8" over the teeth of the hole saw."When cutting metals, use a high-quality cutting oil, if possible. This facilitates smooth running and extends the hole saw service life. Exception: when working on aluminum, use kerosene instead of cutting oil.Bi-metal hole saws are suitable for work on stainless steel (INOX). In order to avoid corrosion, remove any particles that develop from the workpiece during work. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Make sure that all the teeth are applied evenly. To prevent tooth breakage, avoid swinging movements during sawing.Avoid overheating the saw.Observe the maximum cutting depth.The 1-1/4" diameter is designed for cutting out 1-1/4" holes for sink fittings.The 1-3/8" diameter is designed for cutting out holes for plumbing and heating pipes, hollow wall junction boxes, and halogen spots.The 1-8/16" diameter is designed for cutting out holes for plumbing and waste pipes.The 2-3/8" diameter is designed for cutting out 2-3/8" holes for built-in lights.The 2-3/4" diameter is designed for cutting out 2-3/4" holes for hollow wall junction boxes.The 4-1/8" diameter is designed for cutting out holes for exhaust air pipes.Safety notesWhen using shank extensions, the recommended hole saw rotational speed must not be exceeded in order to prevent accidents.Workpiece materialsAluminumBrassBronzeChipboardCopperHard non-ferrous metalHardwoodOther non-ferrous metalsPlasticsSoft aluminium alloysSoft non-ferrous metalSoft woodStainless steel (INOX)SteelSteel, cast steelSteels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tough aluminium alloysWoodZincApplicationsCutting out holesDrillingCompatible power toolsColumn drillPower drill
HSS twist drill bits, HSSE N INOX
Drill bits with cross grinding for industrial use. Fully ground, right-hand turning to produce precise drill holes due to their high concentricity and exact centering. PFERD offers spiral drills STEEL (118 ° point angle) and INOX (135 ° point angle) versions. High-performance HSSE-Co5 (M35) drill bit for industrial use on INOX and other non-ferrous metals. The fully ground right-hand turning design with cross grinding provides an exact centering drill tip and a high level of concentricity.Special featuresIdeal for tough and hard materials, such as alloyed and high-strength steel, stainless steel (INOX).Robust tip profile.Very durable.Very good temperature resistance due to Co content.Very good chip removal.High concentricity.Exact centering and low feed force thanks to cross grinding.Recommendations for useObserve the recommended rotational speed.When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill service life. Exception: when working on aluminum, use kerosene instead of cutting oil.To avoid corrosion when working on stainless steel (INOX), remove any particles that break away from the workpiece. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Safety notesWear eye protection.Follow the safety instructions.Workpiece materialsAluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCasting scaleChipboardCobalt-based alloysCopperDuctile cast ironElastomersFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalNickel or titanium-based superalloysNickel-based alloys (e.g. Inconell and Hastelloy)OtherOther non-ferrous metalsPlasticsRoller-bearing and ball-bearing steelsSoft aluminium alloysSoft non-ferrous metalSoft titanium alloys (tensile strength 500 N/mm²)Soft woodStainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsThermosetting plasticsTitaniumTitanium alloysTool steelsTough aluminium alloysWhite annealed cast iron (GTW, GJMW)WoodZincApplicationsDrillingCompatible power toolsColumn drillTool machinePower drillRobotStationary machines
HSS twist drill bits, HSSG
Drill bits with cross grinding for industrial use. Fully ground, right-hand turning to produce precise drill holes due to their high concentricity and exact centering. PFERD offers spiral drills STEEL (118 ° point angle) and INOX (135 ° point angle) versions. High-performance HSSG (M2) drill bit for industrial use on STEEL. The fully ground right-hand turning design with cross grinding provides an exact centering drill tip and a high level of concentricity.Special features:Designed for universal use on steel, cast steel, grey cast iron, annealed cast iron, bronze, brass, aluminum.Easy centering.Durable.Very good chip removal.High concentricity.Exact centering and low feed force thanks to cross grinding.Recommendations for use:Observe the recommended rotational speed.When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill service life. Exception: when working on aluminum, use kerosene instead of cutting oil.To avoid corrosion when working on stainless steel (INOX), remove any particles that break away from the workpiece. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Safety notes:Wear eye protection.Follow the safety instructions.Workpiece materials:AluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCasting scaleChipboardCopperDuctile cast ironElastomersFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard non-ferrous metalHardwoodOtherOther non-ferrous metalsPlasticsRoller-bearing and ball-bearing steelsSoft non-ferrous metalSoft titanium alloys (tensile strength 500 N/mm²)Soft woodSteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsThermosetting plasticsTitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)WoodZincApplications:DrillingCompatible power tools:Column drillTool machinePower drillRobotStationary machines
HSSE twist drill bit set INOX
The set contains 21 HSS spiral drills, excellent for industrial use on stainless steel (INOX)and non-ferrous metals. The drills are HSSE-Co5 (M35) and come in a heavy-duty blue plastic case that protects against dirt and damage.Special featuresVery good chip removal.High concentricity.Exact centering and low feed force thanks to cross grinding.Ideal for tough and hard materials, such as alloyed and high-strength steel, stainless steel (INOX).Robust tip profile.Very durable.Very good temperature resistance due to Co content.Recommendations for useObserve the recommended rotational speed.When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill service life. Exception: when working on aluminum, use kerosene instead of cutting oil.To avoid corrosion when working on stainless steel (INOX), remove any particles that break away from the workpiece. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Workpiece materialsAluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCasting scaleChipboardCobalt-based alloysCopperDuctile cast ironElastomersFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalNickel or titanium-based superalloysNickel-based alloys (e.g. Inconell and Hastelloy)OtherOther non-ferrous metalsPlasticsRoller-bearing and ball-bearing steelsSoft aluminium alloysSoft non-ferrous metalSoft titanium alloys (tensile strength 500 N/mm²)Soft woodStainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsThermosetting plasticsTitaniumTitanium alloysTool steelsTough aluminium alloysWhite annealed cast iron (GTW, GJMW)WoodZincCompatible power toolsColumn drillPower drillRobotStationary machines
HSSG twist drill bit set STEEL
This set contains 21 HSS spiral drills, excellent for industrial use on steel and other key materials. The drills are HSSG (M2) and come in a heavy-duty blue plastic case that protects against dirt and damage.Special featuresVery good chip removal.High concentricity.Exact centering and low feed force thanks to cross grinding.Designed for universal use on steel, cast steel, grey cast iron, annealed cast iron, bronze, brass, aluminum.Easy centering.Durable.Recommendations for useWhen drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill service life. Exception: when working on aluminum, use kerosene instead of cutting oil.Observe the recommended rotational speed.Workpiece materialsAluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCasting scaleChipboardCopperDuctile cast ironElastomersFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard non-ferrous metalHardwoodOtherOther non-ferrous metalsPlasticsRoller-bearing and ball-bearing steelsSoft non-ferrous metalSoft titanium alloys (tensile strength 500 N/mm²)Soft woodSteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsThermosetting plasticsTitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)WoodZincCompatible power toolsColumn drillPower drillRobotStationary machines
PFERD 12" Extension for Hole Saw Arbors
PFERD offers a variety of hole saw shanks designed for different hole saw dimensions. PFERD also offers arbor extensions for working on hard-to-reach areas. The bi-metal hole saw arbors EDP 29033 and EDP 29034 can be extended using this arbor extension.Special featuresDesigned for hard-to-reach areas.Ideal for work on hollow walls.Deep holes can be easily sawed.Achieves the required distance between the power tool and the work area.Reduces damage to the workpiece and power tool.Keeps dust out of the power tool during use.
PFERD 2" ALUMASTER Arbor - 3/8" Shank
PFERD offers matching arbors for ALUMASTER high speed discs. For use on flexible shaft drives and straight grinders.
PFERD ALUMASTER High Speed Disc 2"
The innovative ALUMASTER High Speed Disc is a unique product with an extremely high stock removal rate. It is ideal for processing aluminum as it does not generate hazardous or explosive dust. It consists of specially developed tungsten carbide cutting inserts, which are fixed to the High Speed Disc. Special disc for processing aluminum alloys. With its uniquely designed arbor, it can be used both on angle grinders (mounting dia. 3/8") and on straight grinders and flexible shaft drives. It is ideal for working on hard-to-reach areas and delicate components. Guards are not necessary due to the disc diameter of 2". High Speed Disc ALUMASTER HSD-R 2" including pre-mounted tungsten carbide cutting inserts, hexalobular socket key, and plastic box.Special featuresDoes not generate hazardous or explosive aluminum dust.Does not require a dust extraction system.Cost-effective and eco-friendly alternative to grinding wheels and flap discs of comparable weight.Innovative and powerful milling tool designed for maximum safety, extreme durability, and ease of use.Specially developed, turnable, and replaceable tungsten carbide cutting inserts.Exceptionally high stock removal rate.Recommendations for useThe ALUMASTER has been designed primarily for use on aluminum, wrought aluminum alloys, and cast aluminum. It can also machine non-ferrous metals that have a relatively low strength, and it can machine fiber-reinforced plastics. Check this for the specific application on a case-by-case basis.Do not push the disc deep into a workpiece. The milling disc is not a cutting tool.Do not exert unnecessarily high forces on the angle grinder. The ALUMASTER High Speed Disc already works with low forces.When machining workpiece edges, cut along the edge, never across the edge.Do not decelerate the disc while it is touching the workpiece. The cutting inserts may break.Safety notesThe flange nut must be tightened with the appropriate tool, such as a face pin wrench. Clamping systems which are designed to be tightened without the use of an additional tool, i.e. which are tightened by hand, should not be used.Tighten the mounting bolts of the cutting inserts using a torque spanner with a tightening torque of 4 Nm. The part number for the 4 Nm torque spanner is 20135.Loose cutting inserts may break during use. Regularly check to make sure they are attached securely.Workpiece materialsAluminumBrassCopperSoft aluminium alloysTough aluminium alloysZincApplicationsMillingMilling outRoot seam processingSurface workWork on weld seamsWork on fillet weldsCompatible power toolsAngle grinderCordless angle grinderRobotStationary machines
PFERD ALUMASTER High Speed Disc 2" with HICOAT® Inserts
The innovative High Speed Disc ALUMASTER is a unique tool with an extremely high stock removal rate. It is ideal for processing aluminum as it does not generate hazardous or explosive dust. The ALUMASTER includes specially developed tungsten carbide cutting inserts fixed to the High Speed Disc. Special disc for processing particularly challenging aluminum alloys. With the specially developed arbor it cannot only be used on angle grinders (mounting dia. 3/8“), but also on straight grinders and flexible shaft drives. The cutting inserts come with a HICOAT® coating. It is highly suitable for working on hard-to-reach areas and delicate components. Due to the disc diameter of 2“, guards are not necessary. High Speed Disc ALUMASTER HSD-R 2" HICOAT® including pre-mounted tungsten carbide cutting inserts, hexalobular socket key, and plastic box.Special featuresDoes not generate hazardous or explosive aluminum dust.Does not require a dust extraction system.Cost-effective and eco-friendly alternative to grinding wheels and flap discs of comparable weight.Innovative and powerful milling tool designed for maximum safety, extreme durability, and ease of use.Specially developed, turnable, and replaceable tungsten carbide cutting inserts.Exceptionally high stock removal rate.Extremely high degree of hardness, very low friction coefficient, very low tendency towards adhesion, improved surface quality, and reduced burr formation, all due to the HICOAT® coatingRecommendations for useThe ALUMASTER has been designed primarily for use on aluminum, wrought aluminum alloys, and cast aluminum. It can also machine non-ferrous metals that have a relatively low strength, and it can machine fiber-reinforced plastics. Check this for the specific application on a case-by-case basis.Do not push the disc deep into a workpiece. The milling disc is not a cutting tool.Do not exert unnecessarily high forces on the angle grinder. The ALUMASTER High Speed Disc already works with low forces.When machining workpiece edges, cut along the edge, never across the edge.Do not decelerate the disc while it is touching the workpiece. The cutting inserts may break.HICOAT® coating allows for use on very complex materials like cast aluminum alloys with 5-10% silicon content, sticky and greasy materials, abrasive cast aluminum alloys with a silicon content over 15%, abrasive materials like fibre-reinforced plastics (FVK), and non-ferrous alloys that are stronger than aluminum (bronze, brass, etc.).Safety notesThe flange nut must be tightened with the appropriate tool, such as a face pin wrench. Clamping systems which are designed to be tightened without the use of an additional tool, i.e. which are tightened by hand, should not be used.Tighten the mounting bolts of the cutting inserts using a torque spanner with a tightening torque of 4 Nm. The part number for the 4 Nm torque spanner is 20135.Loose cutting inserts may break during use. Regularly check to make sure they are attached securely.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysThermoplasticsTough aluminium alloysZincApplicationsMillingMilling outRoot seam processingSurface workWork on weld seamsWork on fillet weldsCompatible power toolsAngle grinderCordless angle grinderRobotStationary machines
PFERD ALUMASTER High Speed Disc 4-1/2"/5"
The innovative ALUMASTER High Speed Disc is a unique product with an extremely high stock removal rate. It is ideal for processing aluminum as it does not generate hazardous or explosive dust. It consists of specially developed tungsten carbide cutting inserts, which are fixed to the High Speed Disc. Special disc for processing aluminum alloys using an angle grinder. Also designed for peripheral milling and milling out root welds. High Speed Disc ALUMASTER HSD-R 4-1/2"/5" including pre-mounted tungsten carbide cutting inserts, hexalobular socket key, and plastic box.Special featuresDoes not generate hazardous or explosive aluminum dust.Does not require a dust extraction system.Cost-effective and eco-friendly alternative to grinding wheels and flap discs of comparable weight.Innovative and powerful milling tool designed for maximum safety, extreme durability, and ease of use.Specially developed, turnable, and replaceable tungsten carbide cutting inserts.Exceptionally high stock removal rate.Recommendations for useThe ALUMASTER has been designed primarily for use on aluminum, wrought aluminum alloys, and cast aluminum. It can also machine non-ferrous metals that have a relatively low strength, and it can machine fiber-reinforced plastics. Check this for the specific application on a case-by-case basis.Do not push the disc deep into a workpiece. The milling disc is not a cutting tool.Do not exert unnecessarily high forces on the angle grinder. The ALUMASTER High Speed Disc already works with low forces.When machining workpiece edges, cut along the edge, never across the edge.Do not decelerate the disc while it is touching the workpiece. The cutting inserts may break.Safety notesThe flange nut must be tightened with the appropriate tool, such as a face pin wrench. Clamping systems which are designed to be tightened without the use of an additional tool, i.e. which are tightened by hand, should not be used.Tighten the mounting bolts of the cutting inserts using a torque spanner with a tightening torque of 4 Nm. The part number for the 4 Nm torque spanner is 20135.Loose cutting inserts may break during use. Regularly check to make sure they are attached securely.Workpiece materialsAluminumBrassCopperSoft aluminium alloysTough aluminium alloysZincApplicationsMillingMilling outRoot seam processingSurface workWork on weld seamsWork on fillet weldsCompatible power toolsAngle grinderCordless angle grinderRobotStationary machines
PFERD ALUMASTER High Speed Disc 4-1/2"/5" with HICOAT® Inserts
The innovative High Speed Disc ALUMASTER is a unique tool with an extremely high stock removal rate. It is ideal for processing aluminum as it does not generate hazardous or explosive dust. The ALUMASTER includes specially developed tungsten carbide cutting inserts fixed to the High Speed Disc. Special disc for processing aluminum alloys using an angle grinder. Version with HICOAT® coating for processing particularly demanding materials. Also suited to peripheral milling and milling out root seams. HSD-R version for radial applications. High Speed Disc ALUMASTER HSD-R 4-1/2"/5" HICOAT® including pre-mounted tungsten carbide cutting inserts, hexalobular socket key, and plastic box.Special featuresDoes not generate hazardous or explosive aluminum dust.Does not require a dust extraction system.Cost-effective and eco-friendly alternative to grinding wheels and flap discs of comparable weight.Innovative and powerful milling tool designed for maximum safety, extreme durability, and ease of use.Specially developed, turnable, and replaceable tungsten carbide cutting inserts.Exceptionally high stock removal rate.Extremely high degree of hardness, very low friction coefficient, very low tendency towards adhesion, improved surface quality, and reduced burr formation, all due to the HICOAT® coatingRecommendations for useThe ALUMASTER has been designed primarily for use on aluminum, wrought aluminum alloys, and cast aluminum. It can also machine non-ferrous metals that have a relatively low strength, and it can machine fiber-reinforced plastics. Check this for the specific application on a case-by-case basis.Do not push the disc deep into a workpiece. The milling disc is not a cutting tool.Do not exert unnecessarily high forces on the angle grinder. The ALUMASTER High Speed Disc already works with low forces.When machining workpiece edges, cut along the edge, never across the edge.Do not decelerate the disc while it is touching the workpiece. The cutting inserts may break.HICOAT® coating allows for use on very complex materials like cast aluminum alloys with 5-10% silicon content, sticky and greasy materials, abrasive cast aluminum alloys with a silicon content over 15%, abrasive materials like fibre-reinforced plastics (FVK), and non-ferrous alloys that are stronger than aluminum (bronze, brass, etc.).Safety notesThe flange nut must be tightened with the appropriate tool, such as a face pin wrench. Clamping systems which are designed to be tightened without the use of an additional tool, i.e. which are tightened by hand, should not be used.Tighten the mounting bolts of the cutting inserts using a torque spanner with a tightening torque of 4 Nm. The part number for the 4 Nm torque spanner is 20135.Loose cutting inserts may break during use. Regularly check to make sure they are attached securely.Workpiece materialsAluminumBrassBronzeCopperFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Hard aluminium alloysHard non-ferrous metalPlasticsSoft aluminium alloysThermoplasticsTough aluminium alloysZincApplicationsMillingMilling outRoot seam processingSurface workWork on weld seamsWork on fillet weldsCompatible power toolsAngle grinderCordless angle grinderRobotStationary machines
PFERD ALUMASTER Replacement Screw Set M4 - 5 Screws
Specially developed cutting inserts from PFERD are durable and achieve a high stock removal rate. Screw set for PFERD cutting inserts.
PFERD ALUMASTER Torque Wrench - Preset to 35.4 in-lbs. (4 Nm)
Torque wrenches are special tools which make it possible to tighten screws or nuts with a defined force. They enable optimal and secure mounting. WIHA torque wrench with a tightening torque of 35.4 in-lbs (4 Nm) for optimally and securely mounting cutting inserts on the ALUMASTER High Speed Disc.
PFERD ALUMASTER Torque Wrench - Replacement blade
Torque wrenches are special tools which make it possible to tighten screws or nuts with a defined force. They enable optimal and secure mounting.
PFERD Bi-Metal Hole Saw Kit 13 Pieces
The set contains nine bi-metal hole saws in the most common diameters, including accessories, for mechanics in the construction, container, and pipeline industries. It comes in a well-arranged plastic box which protects against dirt and damage. Operating instructions are included. It is possible to use hole saw EDPs 29113 and 29115 with the adapter and washer, EDP 29070. The Allen key and the ejection spring are only available in a set and not individually.Special featuresCost-effective sawing of round cut-outs.Alternating tooth pitch prevents chattering during sawing.High concentricity.Good chip removal.The hole saw is conveniently centered and guided via the replaceable bi-metal pilot drill.Hole saw arbor comes with an ejection spring for improved ejection of the cut material.Recommendations for useObserve the recommended rotational speed.Clamp the pilot drill in the hole saw arbor and make sure that it projects at least 1/8" over the teeth of the hole saw."When cutting metals, use a high-quality cutting oil, if possible. This facilitates smooth running and extends the hole saw service life. Exception: when working on aluminum, use kerosene instead of cutting oil.Bi-metal hole saws are suitable for work on stainless steel (INOX). In order to avoid corrosion, remove any particles that develop from the workpiece during work. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Make sure that all the teeth are applied evenly. To prevent tooth breakage, avoid swinging movements during sawing.Avoid overheating the saw.Safety notesWhen using shank extensions, the recommended hole saw rotational speed must not be exceeded in order to prevent accidents.Workpiece materialsAluminumHard non-ferrous metalPlasticsStainless steel (INOX)Steel, cast steelApplicationsCutting out holesDrillingCompatible power toolsColumn drillPower drill
PFERD Hole Saw Arbor Adapter for 1-1/4" to 1-1/2" Hole Saws
PFERD offers hole saw adapters. These adapters allow for quick and easy switching between hole saws while using the same arbor. Hole saws 29111 through 29115 can be used with the arbor adapter EDP 29070, a washer, and the hole saw arbor 29033 or 29036.
PFERD Hole Saw Arbor Repair Kit
These service sets from PFERD allow the most common parts to be replaced in case of loss or damage. PFERD offers a replacement parts set for hole saw arbors and a service set for the ALUMASTER High Speed Disc. Using this replacement set, the most common hole saw parts are replaceable in case of loss or damage. This set includes two ejection springs, two hexagon socket head screws, and an hexagon socket wrench
PFERD Quick-Mounting System for Hole Saws
PFERD offers a quick-mounting system for easily and quickly using bi-metal hole saws with all conventional power drills. PFERD offers a clamping system for easily and quickly using bi-metal hole saws. The quick-mounting system and the two three-part adapter sets, which fit the hole saw diameter, enable PFERD bi-metal hole saw to conveniently be used on all conventional power drills.Special featuresQuickly and easily swap different hole saws.After the application is completed, the hole saw and quick-mounting system can be separated without the use of additional tools by simply pressing a button.Quick-mounting system bi-metal hole saw drill.Recommendations for useQuickly and easily screw the adapters into the desired hole saw and clamp them into the quick-mounting system.
Quick-Mounting 3-Adapter Set for 9/16"-1-3/16" Hole Saws
PFERD offers hole saw adapters. These adapters allow for quick and easy switching between hole saws while using the same arbor. These adapter sets contain three adapters with the same dimensions.Recommendations for useQuickly and easily screw the adapters into the desired hole saw and clamp them into the quick-mounting system.Due to the high torque levels involved, when using large hole saws PFERD recommends the use of the PSL quick-mounting systems in conjunction with the AD-PSL 102-210 HEAVY DUTY adapter.
Tungsten carbide burs for robotics, KZW Shape, 1/2" x 1" x 1/4" Shank
Single cut burs are ideal for machining cast iron, steel, stainless steel (INOX), nickel-based alloys, and titanium alloys. These burs have a high stock removal rate and achieve a good surface finish quality. Special bur shape for robot applications. The combination of various bur shapes enables hard-to-reach components to be deburred and chamfered in just one operation.Special featuresLess programming needed due to fewer product changes.High-quality HICOAT® coating for a longer tool life and improved performance.Ideal surface finish.High surface quality.Work on almost all materials up to 940 HV (68 HRC).Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCobalt-based alloysCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)High-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingSurface workWorking on edgesWorking on edges (chamfering, rounding)Compatible power toolsRobotStraight grinder
Tungsten carbide burs for robotics, KZW Shape, 1/4" x 1/2" x 1/8" Shank
Single cut burs are ideal for machining cast iron, steel, stainless steel (INOX), nickel-based alloys, and titanium alloys. These burs have a high stock removal rate and achieve a good surface finish quality. Special bur shape for robot applications. The combination of various bur shapes enables hard-to-reach components to be deburred and chamfered in just one operation.Special featuresLess programming needed due to fewer product changes.High-quality HICOAT® coating for a longer tool life and improved performance.Ideal surface finish.High surface quality.Work on almost all materials up to 940 HV (68 HRC).Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCobalt-based alloysCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)High-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingSurface workWorking on edgesWorking on edges (chamfering, rounding)Compatible power toolsRobotStraight grinder
Tungsten carbide burs for versatile use, Diamond cut, 14° Taper bur with radius end – Shape L
Diamond cut burs are designed for machining stainless steel (INOX), steel, and high-temperature-resistant materials such as nickel-based and cobalt-based alloys. They have high stock removal with short chips, and achieve a good surface finish. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. 14° Taper bur with round radius end, shape L.Special featuresGood stock removal rate due to high quality tungsten carbide, bur shape, cut, and optional coating.Durable.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.High surface quality.Recommendations for useThe smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsBronzeCase-hardened steelsCast steelCobalt-based alloysHard aluminium alloysHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)High-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
Tungsten carbide burs for versatile use, Diamond cut, Ball bur – Shape D
Diamond cut burs are designed for machining stainless steel (INOX), steel, and high-temperature-resistant materials such as nickel-based and cobalt-based alloys. They have high stock removal with short chips, and achieve a good surface finish. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. Ball-shaped bur, shape D.Special featuresGood stock removal rate due to high quality tungsten carbide, bur shape, cut, and optional coating.Durable.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.High surface quality.Recommendations for useFor the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsBronzeCase-hardened steelsCast steelCobalt-based alloysHard aluminium alloysHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)High-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder
Tungsten carbide burs for versatile use, Diamond cut, Cone bur with pointed end – Shape M
Diamond cut burs are designed for machining stainless steel (INOX), steel, and high-temperature-resistant materials such as nickel-based and cobalt-based alloys. They have high stock removal with short chips, and achieve a good surface finish. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. Cone bur with pointed end, shape M.Special featuresGood stock removal rate due to high quality tungsten carbide, bur shape, cut, and optional coating.Durable.The highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.High surface quality.Recommendations for useThe smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsBronzeCase-hardened steelsCast steelCobalt-based alloysHard aluminium alloysHard non-ferrous metalHardened, heat-treated steels over 370 HV (38 HRC)High-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Stainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)TitaniumTitanium alloysTool steelsApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workWork on weld seamsCompatible power toolsFlexible shaft driveTool machineRobotStationary machinesStraight grinder