Shop
High-performance tungsten carbide burs, TOUGH cut, Cylindrical bur with radius end – Shape C
The TOUGH cut has been specially designed for tough operating conditions such as in shipyards, foundries and steel construction. It is also ideal for all demanding production environments where frequent tooth breakages and other damage to conventional burs occur. Cylindrical bur with rounded radius end, shape C.Special featuresThe highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Innovative quick-mounting system guarantees convenient handling and cool grindingMinimized tooth chipping/breakage, splintering, and bur failures due to very robust, high-performance cut.Can also be used at a lower rotational speed.Due to their extreme impact resistance, they are an ideal option when an extended-shank bur is needed.Recommendations for useObserve the recommended rotational speed.The TOUGH cut can be used on materials up to 580 HV (54 HRC). For hard materials, it is recommended to test the bur on the same material before using on the actual workpiece.TOUGH cut carbide burs are also designed for high-impact applications when using shank extensions, for applications with a high surface contact angle, for work on narrow contours, and for applications where slower rotational speeds are used.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Safety notesFor safety reasons, the maximum application speeds with contact with the workpiece require a reduction in the recommended speed of tungsten carbide burs with standard shanks. Observe the reduced speeds outlined in the product details.When working with longer shanks, it is crucial that the bur is in contact with the workpiece (or inserted in the hole or slot to be machined) before the power tool is turned on. As a rule, the bur must remain in contact with the workpiece for as long as the machine is running. Failure to observe this procedure may result in shank failure (bending) and hence an increased risk of accidents. If continuous contact between the tool and the workpiece is not guaranteed during use, the maximum idling speeds must not be exceeded.Not designed for robotic or stationary applications due to risk of bending. Use only rigid clamping systems/power tools.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)Case-hardened steelsCast ironCast steelGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)SteelSteel materials with a hardness > 54 HRCSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveStraight grinder
High-performance tungsten carbide burs, TOUGH cut, Oval bur – Shape E
The TOUGH cut has been specially designed for tough operating conditions such as in shipyards, foundries and steel construction. It is also ideal for all demanding production environments where frequent tooth breakages and other damage to conventional burs occur. Oval bur.Special featuresThe highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Innovative quick-mounting system guarantees convenient handling and cool grindingMinimized tooth chipping/breakage, splintering, and bur failures due to very robust, high-performance cut.Can also be used at a lower rotational speed.Due to their extreme impact resistance, they are an ideal option when an extended-shank bur is needed.Recommendations for useObserve the recommended rotational speed.The TOUGH cut can be used on materials up to 580 HV (54 HRC). For hard materials, it is recommended to test the bur on the same material before using on the actual workpiece.TOUGH cut carbide burs are also designed for high-impact applications when using shank extensions, for applications with a high surface contact angle, for work on narrow contours, and for applications where slower rotational speeds are used.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)Case-hardened steelsCast ironCast steelGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)SteelSteel materials with a hardness > 54 HRCSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveStraight grinder
High-performance tungsten carbide burs, TOUGH cut, Tree bur with pointed end – Shape G
The TOUGH cut has been specially designed for tough operating conditions such as in shipyards, foundries and steel construction. It is also ideal for all demanding production environments where frequent tooth breakages and other damage to conventional burs occur. Tree bur with pointed end, shape G.Special featuresThe highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Innovative quick-mounting system guarantees convenient handling and cool grindingMinimized tooth chipping/breakage, splintering, and bur failures due to very robust, high-performance cut.Can also be used at a lower rotational speed.Due to their extreme impact resistance, they are an ideal option when an extended-shank bur is needed.Recommendations for useObserve the recommended rotational speed.The TOUGH cut can be used on materials up to 580 HV (54 HRC). For hard materials, it is recommended to test the bur on the same material before using on the actual workpiece.TOUGH cut carbide burs are also designed for high-impact applications when using shank extensions, for applications with a high surface contact angle, for work on narrow contours, and for applications where slower rotational speeds are used.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)Case-hardened steelsCast ironCast steelGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)SteelSteel materials with a hardness > 54 HRCSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveStraight grinder
High-performance tungsten carbide burs, TOUGH cut, Tree bur with radius end – Shape F
The TOUGH cut has been specially designed for tough operating conditions such as in shipyards, foundries and steel construction. It is also ideal for all demanding production environments where frequent tooth breakages and other damage to conventional burs occur. Tree bur with radius end, shape F.Special featuresThe highly accurate concentricity enables precise work free from chatter marks. This considerably reduces wear on the bur and power tool or machine.Innovative quick-mounting system guarantees convenient handling and cool grindingMinimized tooth chipping/breakage, splintering, and bur failures due to very robust, high-performance cut.Can also be used at a lower rotational speed.Due to their extreme impact resistance, they are an ideal option when an extended-shank bur is needed.Recommendations for useObserve the recommended rotational speed.The TOUGH cut can be used on materials up to 580 HV (54 HRC). For hard materials, it is recommended to test the bur on the same material before using on the actual workpiece.TOUGH cut carbide burs are also designed for high-impact applications when using shank extensions, for applications with a high surface contact angle, for work on narrow contours, and for applications where slower rotational speeds are used.The smaller the bur diameter is in the area being used, the higher the recommended rotational speed can be.For the most cost-effective bur use, work with higher rotational/peripheral speeds. For burs with a 1/4" shank diameter, use power tools with a power output from 300 watts.Safety notesFor safety reasons, the maximum application speeds with contact with the workpiece require a reduction in the recommended speed of tungsten carbide burs with standard shanks. Observe the reduced speeds outlined in the product details.When working with longer shanks, it is crucial that the bur is in contact with the workpiece (or inserted in the hole or slot to be machined) before the power tool is turned on. As a rule, the bur must remain in contact with the workpiece for as long as the machine is running. Failure to observe this procedure may result in shank failure (bending) and hence an increased risk of accidents. If continuous contact between the tool and the workpiece is not guaranteed during use, the maximum idling speeds must not be exceeded.Not designed for robotic or stationary applications due to risk of bending. Use only rigid clamping systems/power tools.Workpiece materialsAnnealed cast ironBlack annealed cast iron (GTS, GJMB)Case-hardened steelsCast ironCast steelGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)SteelSteel materials with a hardness > 54 HRCSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tool steelsWhite annealed cast iron (GTW, GJMW)ApplicationsCutting out holesDeburringLevelingMillingMilling outSurface workCompatible power toolsFlexible shaft driveStraight grinder
Holder for hand deburrer
Technical informationPFERD Hand Deburrer HandleItem number12605005EDP no.19500PFERD TOOLS typeH 4Packaging unit1 EACHPFERD offers holders for a range of files and file blades. The PFERD product range includes riffler file holders, adjustable holders for car body files and holders for file blades, tungsten carbide files and hand deburrers. Hand deburrer for efficient deburring, chamfering and reworking of different materials and contours. Hard-to-reach areas, bores, inner and outer diameters, and thread and grooves can easily be worked on by hand.Compatible power toolsManual application
Hole Saw Arbor 3/8" Hex. Shank - 1/2-20 UNF Thread
PFERD offers a variety of hole saw shanks designed for different hole saw dimensions. PFERD also offers arbor extensions for working on hard-to-reach areas. Hole saw arbors are designed for mounting the hole saw and the pilot drill. They are available in three sizes. All hole saw arbors come with an ejection spring to allow for better ejection of the sawn material. The hole saw arbor EDP 29033 comes with bi-metal pilot drill EDP 29040 and an ejection spring.
Hole Saw Replacement Pilot Drill for Arbor 29036
Pilot drills for bi-metal hole saw arbors and quick mounting hole saw systems. Bi-metal pilot drills for use with bi-metal hole saw arbors and quick-mounting systems.ApplicationsDrillingCompatible power toolsColumn drill
Hoof rasps hand
Technical informationPFERD Hoof Plane File 14" Milled ToothItem number13180350CutmilledEDP no.15040Height1/4 InchIncl. handlewithoutLength14 InchPFERD TOOLS type3515Width1.75 InchPackaging unit1 EACHPFERD hoof rasps are good for hoof and horn care. Rectangular file, tanged and cut on four sides. One fine side and one coarse side. Designed for straightening the hoof surface, finishing the hoof wall, filing the toes, and working on the hoof nails after undercutting.Special featuresDurable.Very good surface quality.Effort-saving and reduces back strain.Comfortable filing for worker, and easy on the animal.Recommendations for useThe PFERD hoof plane can be used with commercially available file handles in the appropriate sizes.Workpiece materialsWoodApplicationsChamferingDeburringRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
HSS hole saws thread version 1/2-20 UNF
Hole saws are made from tough, shatter-proof, sturdy HSS bi-metal. The saw teeth are made from high-quality M42 material. They are used for cutting out holes. Arbors with a 1/2-20 thread are part numbers 29033 and 29036.Special featuresCost-effective sawing of round cut-outs.Alternating tooth pitch prevents chattering during sawing.High concentricity.Good chip removal.The hole saw is conveniently centered and guided via the replaceable bi-metal pilot drill.Hole saw arbor comes with an ejection spring for improved ejection of the cut material.Recommendations for useObserve the recommended rotational speed.Clamp the pilot drill in the hole saw arbor and make sure that it projects at least 1/8" over the teeth of the hole saw."When cutting metals, use a high-quality cutting oil, if possible. This facilitates smooth running and extends the hole saw service life. Exception: when working on aluminum, use kerosene instead of cutting oil.Bi-metal hole saws are suitable for work on stainless steel (INOX). In order to avoid corrosion, remove any particles that develop from the workpiece during work. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Make sure that all the teeth are applied evenly. To prevent tooth breakage, avoid swinging movements during sawing.Avoid overheating the saw.Observe the maximum cutting depth.The 1" diameter is designed for cutting out holes for plumbing and heating pipes.The 1-3/16" diameter is designed for cutting out holes for plumbing and heating pipes.Safety notesWhen using shank extensions, the recommended hole saw rotational speed must not be exceeded in order to prevent accidents.Workpiece materialsAluminumBrassBronzeChipboardCopperHard non-ferrous metalHardwoodOther non-ferrous metalsPlasticsSoft aluminium alloysSoft non-ferrous metalSoft woodStainless steel (INOX)SteelSteel, cast steelSteels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tough aluminium alloysWoodZincApplicationsCutting out holesDrillingCompatible power toolsColumn drillPower drill
HSS hole saws thread version 5/8-18 UNF
Hole saws are made from tough, shatter-proof, sturdy HSS bi-metal. The saw teeth are made from high-quality M42 material. They are used for cutting out holes. The arbor with a 5/18-18 thread is part number 29034.Special featuresCost-effective sawing of round cut-outs.Alternating tooth pitch prevents chattering during sawing.High concentricity.Good chip removal.The hole saw is conveniently centered and guided via the replaceable bi-metal pilot drill.Hole saw arbor comes with an ejection spring for improved ejection of the cut material.Recommendations for useObserve the recommended rotational speed.Clamp the pilot drill in the hole saw arbor and make sure that it projects at least 1/8" over the teeth of the hole saw."When cutting metals, use a high-quality cutting oil, if possible. This facilitates smooth running and extends the hole saw service life. Exception: when working on aluminum, use kerosene instead of cutting oil.Bi-metal hole saws are suitable for work on stainless steel (INOX). In order to avoid corrosion, remove any particles that develop from the workpiece during work. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Make sure that all the teeth are applied evenly. To prevent tooth breakage, avoid swinging movements during sawing.Avoid overheating the saw.Observe the maximum cutting depth.The 1-1/4" diameter is designed for cutting out 1-1/4" holes for sink fittings.The 1-3/8" diameter is designed for cutting out holes for plumbing and heating pipes, hollow wall junction boxes, and halogen spots.The 1-8/16" diameter is designed for cutting out holes for plumbing and waste pipes.The 2-3/8" diameter is designed for cutting out 2-3/8" holes for built-in lights.The 2-3/4" diameter is designed for cutting out 2-3/4" holes for hollow wall junction boxes.The 4-1/8" diameter is designed for cutting out holes for exhaust air pipes.Safety notesWhen using shank extensions, the recommended hole saw rotational speed must not be exceeded in order to prevent accidents.Workpiece materialsAluminumBrassBronzeChipboardCopperHard non-ferrous metalHardwoodOther non-ferrous metalsPlasticsSoft aluminium alloysSoft non-ferrous metalSoft woodStainless steel (INOX)SteelSteel, cast steelSteels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)Tough aluminium alloysWoodZincApplicationsCutting out holesDrillingCompatible power toolsColumn drillPower drill
HSS twist drill bits, HSSE N INOX
Drill bits with cross grinding for industrial use. Fully ground, right-hand turning to produce precise drill holes due to their high concentricity and exact centering. PFERD offers spiral drills STEEL (118 ° point angle) and INOX (135 ° point angle) versions. High-performance HSSE-Co5 (M35) drill bit for industrial use on INOX and other non-ferrous metals. The fully ground right-hand turning design with cross grinding provides an exact centering drill tip and a high level of concentricity.Special featuresIdeal for tough and hard materials, such as alloyed and high-strength steel, stainless steel (INOX).Robust tip profile.Very durable.Very good temperature resistance due to Co content.Very good chip removal.High concentricity.Exact centering and low feed force thanks to cross grinding.Recommendations for useObserve the recommended rotational speed.When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill service life. Exception: when working on aluminum, use kerosene instead of cutting oil.To avoid corrosion when working on stainless steel (INOX), remove any particles that break away from the workpiece. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Safety notesWear eye protection.Follow the safety instructions.Workpiece materialsAluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCasting scaleChipboardCobalt-based alloysCopperDuctile cast ironElastomersFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalNickel or titanium-based superalloysNickel-based alloys (e.g. Inconell and Hastelloy)OtherOther non-ferrous metalsPlasticsRoller-bearing and ball-bearing steelsSoft aluminium alloysSoft non-ferrous metalSoft titanium alloys (tensile strength 500 N/mm²)Soft woodStainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsThermosetting plasticsTitaniumTitanium alloysTool steelsTough aluminium alloysWhite annealed cast iron (GTW, GJMW)WoodZincApplicationsDrillingCompatible power toolsColumn drillTool machinePower drillRobotStationary machines
HSS twist drill bits, HSSG
Drill bits with cross grinding for industrial use. Fully ground, right-hand turning to produce precise drill holes due to their high concentricity and exact centering. PFERD offers spiral drills STEEL (118 ° point angle) and INOX (135 ° point angle) versions. High-performance HSSG (M2) drill bit for industrial use on STEEL. The fully ground right-hand turning design with cross grinding provides an exact centering drill tip and a high level of concentricity.Special features:Designed for universal use on steel, cast steel, grey cast iron, annealed cast iron, bronze, brass, aluminum.Easy centering.Durable.Very good chip removal.High concentricity.Exact centering and low feed force thanks to cross grinding.Recommendations for use:Observe the recommended rotational speed.When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill service life. Exception: when working on aluminum, use kerosene instead of cutting oil.To avoid corrosion when working on stainless steel (INOX), remove any particles that break away from the workpiece. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Safety notes:Wear eye protection.Follow the safety instructions.Workpiece materials:AluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCasting scaleChipboardCopperDuctile cast ironElastomersFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard non-ferrous metalHardwoodOtherOther non-ferrous metalsPlasticsRoller-bearing and ball-bearing steelsSoft non-ferrous metalSoft titanium alloys (tensile strength 500 N/mm²)Soft woodSteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsThermosetting plasticsTitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)WoodZincApplications:DrillingCompatible power tools:Column drillTool machinePower drillRobotStationary machines
HSSE twist drill bit set INOX
The set contains 21 HSS spiral drills, excellent for industrial use on stainless steel (INOX)and non-ferrous metals. The drills are HSSE-Co5 (M35) and come in a heavy-duty blue plastic case that protects against dirt and damage.Special featuresVery good chip removal.High concentricity.Exact centering and low feed force thanks to cross grinding.Ideal for tough and hard materials, such as alloyed and high-strength steel, stainless steel (INOX).Robust tip profile.Very durable.Very good temperature resistance due to Co content.Recommendations for useObserve the recommended rotational speed.When drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill service life. Exception: when working on aluminum, use kerosene instead of cutting oil.To avoid corrosion when working on stainless steel (INOX), remove any particles that break away from the workpiece. Clean the workpiece chemically or mechanically (etching/polishing, etc.).Workpiece materialsAluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCasting scaleChipboardCobalt-based alloysCopperDuctile cast ironElastomersFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard aluminium alloysHard non-ferrous metalNickel or titanium-based superalloysNickel-based alloys (e.g. Inconell and Hastelloy)OtherOther non-ferrous metalsPlasticsRoller-bearing and ball-bearing steelsSoft aluminium alloysSoft non-ferrous metalSoft titanium alloys (tensile strength 500 N/mm²)Soft woodStainless steel (INOX)SteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsThermosetting plasticsTitaniumTitanium alloysTool steelsTough aluminium alloysWhite annealed cast iron (GTW, GJMW)WoodZincCompatible power toolsColumn drillPower drillRobotStationary machines
HSSG twist drill bit set STEEL
This set contains 21 HSS spiral drills, excellent for industrial use on steel and other key materials. The drills are HSSG (M2) and come in a heavy-duty blue plastic case that protects against dirt and damage.Special featuresVery good chip removal.High concentricity.Exact centering and low feed force thanks to cross grinding.Designed for universal use on steel, cast steel, grey cast iron, annealed cast iron, bronze, brass, aluminum.Easy centering.Durable.Recommendations for useWhen drilling metals, use a high-quality cutting oil or cooling lubricant, if possible. This facilitates smooth running and extends the drill service life. Exception: when working on aluminum, use kerosene instead of cutting oil.Observe the recommended rotational speed.Workpiece materialsAluminumAnnealed cast ironBlack annealed cast iron (GTS, GJMB)BrassBronzeCase-hardened steelsCast ironCast steelCasting scaleChipboardCopperDuctile cast ironElastomersFibre-reinforced thermosetting plastics (GRP, CRP)Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content > 40 %Fibre-reinforced thermosetting plastics (GRP, CRP) with a fibre content ≤ 40 %Grey/nodular cast iron (GG/GJL, GGG/GJS)Hard non-ferrous metalHardwoodOtherOther non-ferrous metalsPlasticsRoller-bearing and ball-bearing steelsSoft non-ferrous metalSoft titanium alloys (tensile strength 500 N/mm²)Soft woodSteelSteel, cast steelSteels over 220 HV (> 95 HB)Steels up to 220 HV (< 95 HB)Steels up to 370 HV (< 38 HRC)ThermoplasticsThermosetting plasticsTitaniumTitanium alloysTool steelsWhite annealed cast iron (GTW, GJMW)WoodZincCompatible power toolsColumn drillPower drillRobotStationary machines
Key file set, cut 2
Technical informationPFERD Key File Set - 6 Pieces 4" Second CutItem number11702100Cut2Cut files typeSecondEDP no.17009Length4 InchPFERD TOOLS type265 APackaging unit1 EACHSecond cut for universal filing work. This set contains key files designed for a variety of different applications. Includes quick-mounting handle in a plastic pouch to protect against dirt and damage. Handle is only available in a set and not individually.Special featuresVersatile.Designed for filing delicate components.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSharpeningSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Long belts, non-woven type
POLIVLIES Surface Conditioning BeltDesigned for universal work on metal surfaces in stationary applications, e.g. removing rough grinding traces, removing oxidation, and light deburring work. Achieve matte and satin-finished surfaces. Long belts are compatible with commonly available belt grinders. POLIVLIES® grit size 100 G = coarse (yellow-brown)Special featuresCost-effective due to high abrasive performance and durability.High tear strength with optimum flexibility.Consistent work results due to high grain adhesion.Recommendations for useUse the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.For best performance, use at a recommended peripheral speed of 1,000-3,000 SFPM.SafetyFollow all safety instructions for abrasive belt use.Technical informationVersioncoarse, yellow-brownWidth2 inGrit100 GPack qty10
Machinist's file flat
Technical informationPFERD Flat File 12" Second CutItem number11103302Cut2Cut files typeSecondEDP no.11014Height9/32 InchIncl. handlewithoutLength12 InchPFERD TOOLS type1122Width1.15625 InchPackaging unit5 EACHPFERD's machinist files meet the highest quality standards. They are long lasting and have very good stock removal rates. Rectangular file, tapered and cut on four sides. Tanged version. Designed for work on rectangular geometries. Second cut for universal filing work. Files come in industrial packaging without handles.Special featuresConsistently high stock removal rate from the tip to the tang.Durable.Application-oriented design.Recommendations for useUse this file for universal workshop applications.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassBronzeCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Machinist's file half-round
Technical informationPFERD Pipeline File 14" Coarse CutItem number18100398Cut1Cut files typeBastardEDP no.11155Height11/32 InchIncl. handlewithoutLength14 InchPFERD TOOLS type1152Width1.375 InchPackaging unit5 EACHPFERD special files are designed for specific uses, such as for processing soft metals and thermosetting plastics, for deburring parts turned on a lathe, or for sharpening cutting tools. Files for working on pipeline weld seams and for removing scale on pipelines. Files come in industrial packaging without handles.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassBronzeCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Machinist's file half-round pointed
Technical informationPFERD Half Round File 10" Second Cut with Handle RetailItem number11235257Cut2Cut files typeSecondEDP no.11027PHeight9/32 InchIncl. handle12617141Length10 InchPFERD TOOLS type1152 SPWidth15/16 InchPackaging unit1 EACHPFERD's machinist files meet the highest quality standards. They are long lasting and have very good stock removal rates. Half-round pointed file, cut on two sides. Tanged version. Designed for filing out concave surfaces and crevices, and for rounding out holes. Second cut for universal filing work. Files come in point-of-sale packaging with ergonomic file handles.Special featuresConsistently high stock removal rate from the tip to the tang.Durable.Application-oriented design.Recommendations for useUse this file for universal workshop applications.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassBronzeCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Machinist's file hand
Technical informationPFERD Flat PLUS File 12" with Handle RetailItem number11215306CutPLUS-cutCut files typePLUS-cutEDP no.11136PHeight9/32 InchIncl. handle12617151Length12 InchPFERD TOOLS type1112Width1.15625 InchPackaging unit1 EACHPFERD's machinist files meet the highest quality standards. They are long lasting and have very good stock removal rates. Rectangular file, cut on three sides, one side uncut. Tanged version. Designed for working on rectangular surfaces. Superior stock removal due to the PLUS cut. Files come in point-of-sale packaging with ergonomic file handles.Special featuresConsistently high stock removal rate from the tip to the tang.Durable.Application-oriented design.Easy and energy-saving due to spade-like filing teeth.No loading when processing soft materials due to a wide chip breaker.Good for all hobby and DIY purposes.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassBronzeCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Machinist's file knife
Technical informationPFERD Knife File 8" Smooth Cut Smooth CutItem number11109203Cut3Cut files typeSmoothEDP no.11057Height3/16 InchIncl. handlewithoutLength8 InchPFERD TOOLS type1172Width27/32 InchPackaging unit10 EACHPFERD's machinist files meet the highest quality standards. They are long lasting and have very good stock removal rates. Triangular file with knife profile, cut on two sides and the narrow edge. Tanged version. For work on very acute-angled and narrow-shaped surfaces. Smooth cut for precision processing and finishing. Files come in industrial packaging without handles.Special featuresConsistently high stock removal rate from the tip to the tang.Durable.Application-oriented design.Recommendations for useUse this file for fine processing and finishing.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassBronzeCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Machinist's file round
Technical informationPFERD Round File 4" Coarse CutItem number11107101Cut1Cut files typeBastardEDP no.11061Incl. handlewithoutLength4 InchPFERD TOOLS type1162Dia. external5/32 InchPackaging unit10 EACHPFERD's machinist files meet the highest quality standards. They are long lasting and have very good stock removal rates. Round file cut all the way around the circumference. Tanged version. Designed for work on circular holes and rounded grooves. Bastard cut for coarse stock removal and roughing. Files come in industrial packaging without handles.Special featuresRapid metal removal and smooth surface finish due to spiral cut.Consistently high stock removal rate from the tip to the tang.Durable.Application-oriented design.Recommendations for useUse this file for roughing or coarse stock removal.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassBronzeCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Machinist's file square
Technical informationPFERD Square File 10" Smooth CutItem number11104253Cut3Cut files typeSmoothEDP no.11092Incl. handlewithoutLength10 InchPFERD TOOLS type1142Width3/8 InchPackaging unit10 EACHPFERD's machinist files meet the highest quality standards. They are long lasting and have very good stock removal rates. Square file, tapered and cut on four sides. Tanged version. Designed for filing angular surfaces. Smooth cut for precision processing and finishing. Files come in industrial packaging without handles.Special featuresConsistently high stock removal rate from the tip to the tang.Durable.Application-oriented design.Recommendations for useUse this file for fine processing and finishing.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassBronzeCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Machinist's file three square
Technical informationPFERD Three Square File 6" Second CutItem number11108152Cut2Cut files typeSecondEDP no.11098Incl. handlewithoutLength6 InchPFERD TOOLS type1132Width15/32 InchPackaging unit10 EACHPFERD's machinist files meet the highest quality standards. They are long lasting and have very good stock removal rates. Triangular file, tapered and cut on all three sides. Tanged version. Designed for filing angular surfaces. Second cut for universal filing work. Files come in industrial packaging without handles.Special featuresConsistently high stock removal rate from the tip to the tang.Durable.Application-oriented design.Recommendations for useUse this file for universal workshop applications.Workpiece materialsSteel, cast steelSteels up to 370 HV (< 38 HRC)ZincAluminumBrassBronzeCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)ApplicationsChamferingDeburringFinishingRoundingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application