Products
Diamond Mounted Point
GritD126Dia. shank1/8 InchDrive typeFlexible shaft driveDrive type 2Tool machineDrive type 3RobotDrive type 4Straight grinderPack qty1Diamond Mounted Point, 1/16" x 5/32"Electroplated diamond and CBN grinding points are used for both wet and dry grinding. The cylindrical shape is suitable for grinding bores, radii and contours using stationary or handheld equipment.Special featuresIdeal for work on tungsten carbideNo chemical wear due to the low working temperaturesLonger service life due to harder diamond grain.ApplicationsDeburringFinishingGrinding outInternal grindingWorking on edges (chamfering, rounding)Materials that can be workedTechnical ceramicsTungsten carbideAbrasive materialsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useCan be used for either dry or wet grinding. If possible, wet grinding is preferable to reduce wear and risk of thermal damage.Generally, the following applies: For optimum economic efficiency, select a grit size that is as coarse as possible and as fine as necessary. Influencing factors include the hardness of the material and the surface quality required.Loaded products can be cleaned using ultrasound. In the event of strong contamination on the coating, use a sharpening block to clean the product.Select as large a tool diameter as possible, as this increases the amount of grit that engages the workpiece. For internal grinding, the maximum tool diameter is 3/4 of the diameter to be ground.The longitudinal feed rate for internal grinding must not exceed 2/3 of the total width per workpiece rotation. The infeed depends on the material to be machined, the cutting speed, the stability of the tool, its holder and the tool drive.Because of the monolayer coating, the drive spindle and tool mounting must have a high concentricity. The finer the grit size used, the more accurate the concentricity needs to be.The power tool needs to have enough drive output on the grinding spindle to meet the required rotational speed, even under load.Dry grinding: 1500-3500 SFPMWet grinding: 3000-5000 SFPM
Diamond Needle File 5-1/2" 6-1/2" x 1/2"
GritD91ShapeBarrette shapeDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" 6-1/2" x 1/2"Diamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2" Feather Edge
GritD91ShapeFeather edgeDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" Feather EdgeDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2" Fine Cut
GritD91ShapeKnife shapeDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" Fine CutDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2" Half Round
GritD91ShapeHalf-roundDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" Half RoundDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2" Hand
GritD91ShapeHand with round edgesDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" HandDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2" Round
GritD91ShapeRoundDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" RoundDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2" Square
GritD91ShapeSquareDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" SquareDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2" Three Square
GritD91ShapeThree squareDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" Three SquareDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2", Crossing oval shape
GritD91ShapeCrossing oval shapeDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2"Diamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2", Flat
GritD91ShapeFlatDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" FlatDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File 5-1/2", Hand
GritD91ShapeHandDrive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File 5-1/2" HandDiamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. Diamond needle files can be used universally in tool making.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Needle File Set - 5 Pieces
The diamond needle file set comes in a sturdy, practical plastic box which protects the tools from damage. This is ideal for keeping in the tool trolley or workbench. Diamond needle files can be used universally in tool making. This set contains one each of the following file shapes: hand, three square, square, half-round, and round
Diamond Needle File Set
GritD91Drive typeManual applicationOverall length5 1/2 InchPack qty1Diamond Needle File Set 5-1/2"The diamond needle file set comes in a sturdy, practical plastic box which protects the tools from damage. This is ideal for keeping in the tool trolley or workbench. Diamond needle files can be used universally in tool making. This set contains one each of the following file shapes: hand, three square, square, half-round, and roundApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Polishing Paste, Cap Color Yellow
Diamond Polishing Paste, Cap Color YellowDiamond polishing pastes allow for quick and efficient work, particularly in tool and die making. Diamond polishing pastes are used for work on hard materials, such as tungsten carbide and hardened steels. They are used in combination with felt polishing elements. Diamond polishing pastes can be diluted and dissolved with water and alcohol. ECO diamond polishing pastes are an affordable option. Grit size according to ISO 6344 = P 14000Special featuresHigh productivity.Quick results.Specialized selection of grit sizes.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useWhen using diamond polishing pastes, use the most coarse paste first.If extensive surface improvements are needed, use several grit sizes one after another, each finer than the previous, cleaning well between pastes.When changing grit size, make sure that a new, clean polishing product (e.g. felt point or felt wheel) is used.Technical informationDrive typeManual applicationGrit1Pack qty1
Diamond Riffler File Set 6 Pieces Medium Cut
The diamond riffler file set comes in a sturdy, practical plastic box which protects the tools from damage. This is ideal for keeping in the tool trolley or workbench. Diamond riffler files are used for work in hard-to-reach areas and on complex geometries. The coating length is 1" on each side of the files." The coating length is 25 mm on both sides of the files. The set contains one each of the following file shapes: crossing oval, hand, square, three square, round.
Diamond Riffler File Set 6 Pieces Medium Cut
GritD126Drive typeManual applicationOverall length6 InchPack qty1Diamond Riffler File Set 6 Pieces Medium CutThe diamond riffler file set comes in a sturdy, practical plastic box which protects the tools from damage. This is ideal for keeping in the tool trolley or workbench. Diamond riffler files are used for work in hard-to-reach areas and on complex geometries. The coating length is 1" on each side of the files." The coating length is 25 mm on both sides of the files. The set contains one each of the following file shapes: crossing oval, hand, square, three square, round.ApplicationsDeburringFinishingLevelingRemoving oxide layersWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Diamond Segmented Cut-Off Wheel
Shape1A1R / DSDrive typeAngle grinderDia. hole7/8 InchMax. RPM12200Pack qty1Diamond Segmented Cut-Off Wheel PSF , 5" x 5/64" x 7/8"PFERD TOOLS diamond cut-off wheels are manufactured in compliance with the highest quality and safety standards. They guarantee optimum cutting results and allow efficient processing of different materials, e.g. concrete, exposed aggregate concrete, clinker brick, hard stone, granite and other abrasive building materials. The product range offers the best tool for any application. General-purpose segmented-edge tool for aggressive, fast cutting with high cutting performance and an ideal tool life. With laser-welded segments.Special featuresHigh quality diamond abrasive grain.Excellent cutting characteristics and short cutting times.Easy cutting and cost-effective.ApplicationsCuttingCutting out holesMaterials that can be workedBrickReinforced concreteSoft stoneConcreteRecommendations for useIf possible, wet grinding is preferable to dry grinding. This reduces tool wear, the risk of thermal damage to the workpiece and dust exposure.Cut using only slight pressure in order to prevent the tool from overheating.Works on angle grinders of all output levels.
Diamond Semi-Flexible File
GritD64Drive typeManual applicationCoatingcompleteOverall length14 InchPack qty1Diamond Semi-Flexible File 14" x 1-3/8" x 3/64"Diamond files and sheets are used when conventional files fail due to the hardness of the workpiece material. Diamond files and sheets are also used for processing hardened steel. Using these products does not generate much heat, which prevents chemical wear. This allows for a longer service life for the high hardness diamond grain. These diamond sheets are ideal for larger surfaces. Convex and concave contours can be worked on with relatively little effort.ApplicationsDeburringFinishingLevelingRemoving oxide layersSurface workWorking on edgesWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTechnical ceramicsTool steelsTungsten carbideAbrasive materialsCase-hardened steelsFerrite (magnetic material)GlassGraphite and synthetic carbonNickel or titanium-based superalloysRecommendations for useOnly apply light pressure to the file, especially when using on workpiece edges.Loaded diamond files can be cleaned in kerosene or anti-static plastic cleaner with a file brush. Alternatively, ultrasonic cleaning is also possible. Often, knocking the file against a hard object is sufficient.Avoid using grease.
Die Grinder Cut-Off Wheel, 3" x .040 x 3/8, SG STEELOX
ShapeEHT / 41 / T1AbrasiveAluminum oxide ADrive typeFlexible shaft drive, Straight grinderMax. RPM25000Pack qty36Performance Line SGThe wide range Performance Line SG offers high-performance solutions for every application and material. Performance Line SG products achieve optimum results with excellent economic efficiency. PFERD offers small cut-off wheels in various dimensions for straight grinders. These general-purpose cut-off wheels are designed to cut steel, stainless steel (INOX), cast iron, aluminum and other materials. General-purpose cut-off wheel for use on straight grinders. High cutting performance and maximum service life. PFERD is a global leader in performance and safety of thin cut-off wheels. We maximize the performance and benefits for our users with: Thinner, faster cutting with minimal burr formation. Highest possible productivity and Comfort and safety. Intensive research, development and targeted implementation in our state-of-the-art production facilities guarantee the highest quality and compliance with safety standards.AdvantagesIdeal for hard-to-reach areas.General-purpose cut-off wheel for many different materials.Fast work due to high cutting performance.Maximum economic efficiency due to maximum durability.ApplicationsCutting of profilesCutting of sheet metalCutting of solid materialCutting out holesMaterials that can be workedStainless steel (INOX)SteelAluminumCast ironNickel-based alloys (e.g. Inconell and Hastelloy)Nickel or titanium-based superalloysOther non-ferrous metalsSafetyNote the maximum rotational speed for the cut-off wheel and arbor – adhere to whichever speed is lower.
Die Grinder Cut-Off Wheel, SG STEELOX
ShapeEHT / 41 / T1AbrasiveAluminum oxide ADrive typeFlexible shaft drive, Straight grinderMax. RPM30000Pack qty50Performance Line SGThe wide range Performance Line SG offers high-performance solutions for every application and material. Performance Line SG products achieve optimum results with excellent economic efficiency. PFERD offers small cut-off wheels in various dimensions for straight grinders. These general-purpose cut-off wheels are designed to cut steel, stainless steel (INOX), cast iron, aluminum and other materials. General-purpose cut-off wheel for use on straight grinders. High cutting performance and maximum service life. PFERD is a global leader in performance and safety of thin cut-off wheels. We maximize the performance and benefits for our users with: Thinner, faster cutting with minimal burr formation. Highest possible productivity and Comfort and safety. Intensive research, development and targeted implementation in our state-of-the-art production facilities guarantee the highest quality and compliance with safety standards.AdvantagesIdeal for hard-to-reach areas.General-purpose cut-off wheel for many different materials.Fast work due to high cutting performance.Maximum economic efficiency due to maximum durability.ApplicationsCutting of profilesCutting of sheet metalCutting of solid materialCutting out holesMaterials that can be workedStainless steel (INOX)SteelAluminumCast ironNickel-based alloys (e.g. Inconell and Hastelloy)Nickel or titanium-based superalloysOther non-ferrous metalsSafetyNote the maximum rotational speed for the cut-off wheel and arbor – adhere to whichever speed is lower.
Die Grinder
Pack qty1Accessory for mounting small cut-off wheels on straight grinders. Rugged product with maximum shank fracture resistance.SafetyNote the maximum rotational speed for the cut-off wheel and arbor – adhere to whichever speed is lower.
DIY File Set - 3 Pieces
Quality files designed for DIY users. Precise, with a high stock removal rate and good durability. Also suitable for sharpening. Each file comes with an ergonomic file handle. Packaged in a cardboard box.
Drum Brush
Technical informationBrush Diameter4 InchFilament MaterialStainless steel wire (INOX)Wire Diameter0.008 InchArbor Hole3/4 InchTrim Length1 InchMax. RPM6000 RPMPack Qty1Excellent for surface structuring work on large workpieces. In order to fulfill the requirements for brushing stainless steel (INOX), PFERD produces all stainless steel (INOX) brushes using 302 stainless steel wire. Practical experience gained from industrial use confirms that this wire quality achieves excellent corrosion resistance with optimum brush life. The wire found in stainless steel (INOX) brushes tends to become magnetic after cold working. All PFERD brush products with stainless steel wire (INOX) are color-coded blue in the Tool Manual. All of these brushes are recommended for use on all stainless steels (INOX), such as 316.;The reason for this is a change in the microstructure caused by deformation (e.g. during the wire drawing process). This does not have any impact on the quality and corrosion resistance of the INOX filament. The filament is still resistant to corrosion. Stainless steel wire (INOX) is temperature-resistant up to 850 °F.AdvantagesCan be used on all common burnishing machines due to keyed arbor hole.Very corrosion-resistant.Creates fine surfaces.ApplicationsCleaningDeburringDerustingRemoving heat discolourationRemoving oxide layersPaint strippingRougheningStructuring (matt finishing, brush matting and satin finishing)Materials that can be workedSoft titanium alloys (tensile strength 500 N/mm²)Stainless steel (INOX)TitaniumTitanium alloysAluminumBronzeCobalt-based alloysHard non-ferrous metalHigh-temperature-resistant materialsNickel-based alloys (e.g. Inconell and Hastelloy)Drive TypesDrum grinders