Shop
4-1/2"/5" ALUMASTER Carbide Insert Set - 10 Inserts
Specially developed cutting inserts from PFERD are durable and achieve a high stock removal rate. Cutting insert set for ALUMASTER High Speed Disc.
4-1/2"/5" ALUMASTER Service Set - TORX Key, 2 Screws, 2 Inserts
These service sets from PFERD allow the most common parts to be replaced in case of loss or damage. PFERD offers a replacement parts set for hole saw arbors and a service set for the ALUMASTER High Speed Disc. For swapping individual cutting inserts on the ALUMASTER High Speed Disc. This set contains two cutting inserts, two screws, and a hexalobular socket wrench.
8" Replacement depth gauge file, Cut 2 for ChainSharp CS-X
PFERD offers replacement files for different filing tools, such as replacement files for paint peelers, replacement file blades for universal chamfer files, chain saw files, and depth gauge files for chain saw sharpeners. Rectangular file with cut on two sides. Designed for the CHAIN SHARP CS-X chain saw sharpener.
Abrasive Benchstand Belt
Abrasive Benchstand BeltFor universal applications from coarse to fine grinding. Long belts are compatible with commonly available belt grinders.Special featuresHigh tear strength with optimum flexibility.Consistent work results due to high grain adhesion.Cost-effective due to high abrasive performance and durability.ApplicationsDeburringStep-by-step fine grindingLevelingSharpeningWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumAnnealed cast ironBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyFollow all safety instructions for abrasive belt use.Technical informationWidth2 inDrive typeBelt grinderGrit36Pack qty10
Abrasive Cord
Abrasive CordHighly flexible, therefore ideal for very fine deburring and finishing work in hard-to-reach places. Ideal for work on very small holes, grooves and cut-outs in tool and mold-making.Special featuresConforms to contours due to high flexibility.Low wear due to high tear strength and very high grain adhesion.ApplicationsCleaningStep-by-step fine grindingRougheningSurface workMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumAnnealed cast ironBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useTrim to the necessary size as needed.Technical informationDia. External0.08 inDrive typeManual applicationGrit120Pack qty1
Abrasive File Belt
Abrasive File BeltFor universal applications from coarse to fine grinding. Short belts are compatible with commonly available belt grinders.Special featuresHigh tear strength with optimum flexibility.Consistent work results due to high grain adhesion.Cost-effective due to high abrasive performance and durability.ApplicationsDeburringStep-by-step fine grindingLevelingSharpeningWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysZincAluminumAnnealed cast ironBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Grey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useUse the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyFollow all safety instructions for abrasive belt use.Technical informationWidth1/4 inDrive typeBelt grinderGrit36Pack qty50
Abrasive spiral bands, conical
Spiral BandFor aggressive grinding with maximum stock removal on hard materials that do not conduct heat well. Consistently high performance due to self-sharpening ceramic oxide grain. Active grinding additives in the coating substantially improve the stock removal rate, prevent loading, and result in cooler grinding. In ISO 2421, abrasive spiral bands are designated as "cylindrical sleeves". GSB = bulk pack of abrasive spiral bandsSpecial featuresThe packaging size is ideally suited to industrial requirements.Abrasive spiral bands fit securely on the rubber drum holder as the holder expands during use.Outstanding service life even under the toughest work conditions, due to special manufacturing.Highest possible cost-effectiveness due to particularly high stock removal rate and aggressiveness of the abrasive.ApplicationsDeburringStep-by-step fine grindingLevelingRougheningSharpeningSurface workWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)TitaniumAluminumAnnealed cast ironBronzeCobalt-based alloysGrey/nodular cast iron (GG/GJL, GGG/GJS)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useTo easily change the abrasive spiral bands, give them a slight clockwise twist and pull them up and off. When doing so, leave the rubber drum holder clamped in the power tool.To ensure the abrasive spiral band is securely attached, follow the minimum speed for the rubber drum holder.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyThe maximum permitted peripheral speed is 6,000 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Do not allow abrasive spiral bands to protrude beyond the rubber drum holder.Technical informationDia. External3/4 inDrive typeFlexible shaft driveGrit36Pack qty100
Abrasive spiral bands, cylindrical
Spiral BandFor coarse grinding work with a high stock removal rate and cool grinding. Active grinding additives in the coating substantially improve the stock removal rate, prevent loading and result in cooler grinding. In ISO 2421, abrasive spiral bands are designated as "cylindrical sleeves". GSB = bulk pack of abrasive spiral bandsSpecial featuresAbrasive spiral bands fit securely on the rubber drum holder as the holder expands during use.Outstanding service life even under the toughest work conditions, due to special manufacturing.Highest possible cost-effectiveness due to particularly high stock removal rate and aggressiveness of the abrasive.ApplicationsDeburringStep-by-step fine grindingLevelingRougheningSharpeningSurface workWork on weld seamsWorking on edgesMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)TitaniumTitanium alloysAnnealed cast ironBronzeCast steelCobalt-based alloysGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Recommendations for useTo easily change the abrasive spiral bands, give them a slight clockwise twist and pull them up and off. When doing so, leave the rubber drum holder clamped in the power tool.To ensure the abrasive spiral band is securely attached, follow the minimum speed for the rubber drum holder.For the best performance, use with a recommended peripheral speed of 4,000-6,000 SFPM.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyThe maximum permitted peripheral speed is 6,000 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Do not allow abrasive spiral bands to protrude beyond the rubber drum holder.Technical informationDia. External1 1/8 inDrive typeFlexible shaft driveGrit36Pack qty100
Acid Brush
Technical informationFilament MaterialHorsehairTrim Length3/4 InchPack Qty144Small, high-quality brushes for applying flux film and other coatings. Natural horsehair fibers minimize contamination in brazing and soldering applications.ApplicationsApplicationDrive TypesManual application
Knock-Out Bushing
Technical informationShapeTC Wheel bushingPack Qty10PFERD offers various arbor hole adapters for wheel brushes.AdvantagesEnables the use of brushes on all power tools as the hole diameter is adjusted to the required dimension.Machined metal components for accurate fit.
All-Purpose File 8" Second Cut with Handle
PFERD special files are designed for specific uses, such as for processing soft metals and thermosetting plastics, for deburring parts turned on a lathe, or for sharpening cutting tools. Rectangular file with different cuts on three sides. Tanged version with ergonomic file handle. Cross cut 1 on front side for roughing, single cut 2 on back side, and edge for sharpening. Combination of cross cut for coarse roughing and machining on one side and a single cut on the other side for sharpening cutting tools. Files come in point-of-sale packaging with ergonomic file handles.
Aluminum Flat File 10" Cut
PFERD special files are designed for specific uses, such as for processing soft metals and thermosetting plastics, for deburring parts turned on a lathe, or for sharpening cutting tools. Rectangular file, tanged and special cut on three sides, one edge uncut. Designed to work well on soft metals. Special cut specifically designed for coarse stock removal on soft metals such as aluminum.
Aluminum Half Round File 10" Cut
PFERD special files are designed for specific uses, such as for processing soft metals and thermosetting plastics, for deburring parts turned on a lathe, or for sharpening cutting tools. Half-round file, tanged with cut on two sides. Excellent filing performance due to the PFERD spiral cut on the half-round side. Designed to work well on soft metals. Special cut specifically designed for coarse stock removal on soft metals such as aluminum.
Angle Grinder Flap Wheel
Angle Grinder Flap WheelWith unmounted flap wheels, coated abrasive flaps are arranged radially around the core in a fan-like structure. The flexible flaps perfectly adapt to surface contours. The abrasive grain is embedded in the sturdy, flexible cloth backing material with a resinoid bond. In ISO 5429, unmounted flap wheels are designated as "flap wheels." The ideal flap wheel for use on angle grinders in assembly shop operations. For universal applications from coarse to fine grinding.Special featuresConforms to contours due to high flexibility.Consistently high stock removal rate throughout the entire service life as new, aggressive abrasive is constantly exposed.Can be used face-down very close to edges and in corners thanks to special clamping system.Can be mounted directly on the angle grinder without additional clamping devices.ApplicationsDeburringStep-by-step fine grindingLevelingStructuring (matt finishing, brush matting and satin finishing)Surface workWork on weld seamsMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)AluminumAnnealed cast ironBrassCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useFlap wheel wear and the thermal load on the workpiece are reduced by decreasing the contact pressure and peripheral speed, and by adding grinding oil.Stock removal rate should be increased by using a coarser grit, not by increasing the contact pressure. This avoids unnecessary flap wheel wear and prevents the thermal load of the workpiece.Increasing the speed results in a slightly finer surface quality. An increase in contact pressure results in a slightly coarser surface. The softer the workpiece material, the coarser the resulting surface (when using the same grit size).Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.For the best results, use a power tool with 1,000–1,500 watts.For best performance, use at a recommended peripheral speed of 7,900-9,800 SFPM.SafetyUnmounted flap wheels should only be used with the appropriate clamping flanges.The contact pressure has to be reduced significantly when the optimum rotational speed is exceeded.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.The maximum permitted peripheral speed is 15,800 SFPM.Technical informationDia. External4 1/2 inWidth3/4 inDrive typeAngle grinderGrit40Max. RPM13300Pack qty2
Bench grinding wheels CARBIDE
Bench grinding wheels CARBIDEPFERD bench grinding wheels have been designed to work with standard bench grinders. CARBIDE type bench grinding wheels are used on hard materials, such as for sharpening tungsten carbide tools.Special featuresDurable.High dimensional stability.High abrasive performance.Integrated telescopic bushings for mounting on almost any bench grinder spindle.ApplicationsDeburringSharpeningWorking on edges (chamfering, rounding)Materials that can be workedSteel materials with a hardness > 54 HRCTungsten carbideGlassHardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useDressing the wheel on a regular basis exposes sharp grain and maintains an even grinding area.Constantly adjust the workpiece support to the grinding wheel diameter (gap width max. 1/8").SafetyThe maximum permitted peripheral speed is 6,900 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Before clamping, the grinding tool must be ring tested to make sure that it does not have any cracks (undamaged grinding tools give a clear tone).
Bench grinding wheels HSS
Bench grinding wheels HSSPFERD bench grinding wheels have been designed to work with standard bench grinders. The HSS design is ideal for sharpening HSS pilot drills or machining other high-alloy steels.Special featuresDurable.High dimensional stability.High abrasive performance.Integrated telescopic bushings for mounting on almost any bench grinder spindle.ApplicationsDeburringSharpeningWorking on edges (chamfering, rounding)Materials that can be workedTool steelsCase-hardened steelsHardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useDressing the wheel on a regular basis exposes sharp grain and maintains an even grinding area.Constantly adjust the workpiece support to the grinding wheel diameter (gap width max. 1/8").SafetyThe maximum permitted peripheral speed is 6,900 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Before clamping, the grinding tool must be ring tested to make sure that it does not have any cracks (undamaged grinding tools give a clear tone).
Bench grinding wheels UNIVERSAL
Bench grinding wheels UNIVERSALPFERD bench grinding wheels have been designed to work with standard bench grinders. The UNIVERSAL type is ideal for general workshop use.Special featuresDurable.High dimensional stability.High abrasive performance.Integrated telescopic bushings for mounting on almost any bench grinder spindle.ApplicationsDeburringSharpeningWorking on edges (chamfering, rounding)Materials that can be workedStainless steel (INOX)SteelCast ironRecommendations for useDressing the wheel on a regular basis exposes sharp grain and maintains an even grinding area.Constantly adjust the workpiece support to the grinding wheel diameter (gap width max. 1/8").SafetyThe maximum permitted peripheral speed is 6,900 SFPM.For safety reasons, the maximum permitted rotational speed indicated must never be exceeded.Before clamping, the grinding tool must be ring tested to make sure that it does not have any cracks (undamaged grinding tools give a clear tone).
Bore polisher
Bore polisherThe flaps made of coated abrasive are arranged radially around the axis in a fan-type structure. Designed for fine grinding. In ISO 3919, mounted flap wheels are designated as "flap wheels with shaft."Special featuresConforms to contours due to high flexibility.Consistently high stock removal rate throughout the entire service life as new, aggressive abrasive is constantly exposed.ApplicationsCleaningDeburringStep-by-step fine grindingGrinding outLevelingRemoving oxide layersSurface workWork on weld seamsMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)AluminumBrassCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useFlap wheel wear and the thermal load on the workpiece are reduced by decreasing the contact pressure and peripheral speed, and by adding grinding oil.Stock removal rate should be increased by using a coarser grit, not by increasing the contact pressure. This avoids unnecessary flap wheel wear and prevents the thermal load of the workpiece.Increasing the speed results in a slightly finer surface quality. An increase in contact pressure results in a slightly coarser surface. The softer the workpiece material, the coarser the resulting surface (when using the same grit size).For the best performance, use with a recommended peripheral speed of 3,000-4,000 SFPM. This provides an ideal compromise between stock removal rate, surface quality, thermal load on the workpiece and tool wear.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyFor safety reasons, the maximum permitted rotational speed indicated must never be exceeded.The contact pressure has to be reduced significantly when the optimum rotational speed is exceeded.Technical informationDia. External5/8 inWidth3/4 inDia. shank1/4 InchDrive typeFlexible shaft driveGrit120Max. RPM31800Pack qty10
Broom Head - Fine Sweep, Horsehair/nylon mix, 79189217
Technical informationHorsehair/nylon mix, 79189217Filament MaterialHorsehair/nylon mixTrim Length3 InchPack Qty12Fine sweeping brooms for light-duty sweeping on smooth surfaces. Lacquered hardwood. High-quality sweep for best cleaning of fine dirt on smooth floors. Horsehair-nylon mix stapled into lacquered hardwood block with two threaded handle holes.AdvantagesNatural horsehair fibers minimize contamination in brazing and soldering applications.ApplicationsCleaningSweepingDrive TypesManual application
Buffing Drum, Soft Cotton Yarn
Buffing Drum, Soft Cotton YarnDue to the soft cotton yarn, ideal for high-gloss polishing with polishing pastes in tool and die-making. The ends of the threads provide optimum absorption of the polishing paste. Please order corresponding polishing pastes and arbor separately.Special featuresConforms to contours due to high flexibility.Can be freely shaped, meaning they can be used on complicated geometries.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Technical informationDia. External4 inWidth4 inDrive typeDrum grindersMax. RPM3500Pack qty1
Cant saw file
Technical informationPFERD Cant Saw File 8" Three Square Second CutItem number11633202Cut2Cut files typeSecondEDP no.17014Height1/2 InchLength8 InchPFERD TOOLS type1230Width7/8 InchPackaging unit10 EACHThree square saw files from PFERD are triangular tapered tanged files. The saw files are suitable for use on steel and cast steel and especially suitable for sharpening sawing tools. PFERD offers three square saw files in various versions and shapes. Triangular file, tanged. Cut on three sides, non-equilateral triangular shape. Second cut for universal sharpening tasks. Files come in industrial packaging without handles.Special featuresGood stock removal rate.Durable.Versatile.Workpiece materialsSteels up to 370 HV (< 38 HRC)Cast steelApplicationsSharpeningCompatible power toolsManual application
Car body file blades hand
Technical informationPFERD Car Body File 14" Milled Tooth Cut 1Item number14101351Cut1EDP no.14006Height7/32 InchLength14 InchPFERD TOOLS type299 bWidth1.34375 InchVersioncoarsePackaging unit1 EACHCar body file blades in the holder can be precisely tensioned and adjusted to match the surface contour of the workpiece. Radial special coarse cut for very coarse stock removal and roughing. The cut is designed to achieve score-free surfaces. These car body files comes in industrial packaging without car body file holders. They are also individually packaged in plastic sleeves.Special featuresThe tensioning system makes it easy to adjust the bending radius of the file.Precise handling.Razor-sharp tooth edges.Convex shape of the file prevents unwanted scratches.Workpiece materialsSteels up to 370 HV (< 38 HRC)AluminumApplicationsLevelingSurface workCompatible power toolsManual application
Car body file holder
Technical informationPFERD Adjustable Holder 12" for Car Body FileItem number14000167EDP no.14012PFERD TOOLS typeKFHPackaging unit1 EACHPFERD offers holders for a range of files and file blades. The PFERD product range includes riffler file holders, adjustable holders for car body files and holders for file blades, tungsten carbide files and hand deburrers. Adjustable car body file holders allow precise tensioning of the file blade to match the workpiece surface contour. The tensioning system makes it easy to adjust the bending radius of the file to be adjusted. This ergonomic and particularly lightweight holder enables precise tensioning of car body file blades to match the workpiece surface contour.Special featuresThe tensioning system makes it easy to adjust the bending radius of the file.Particularly lightweight plastic design containing no plasticizers.Can be curved or straight, allowing it to be used on a specific spot or a wide area.Vibration-damping rubber pad reduces fatigue.Compatible power toolsManual application
Car body files tanged hand
Technical informationPFERD Car Body File 14" Cut 3 Milled Tooth with TangItem number14103353Cut3Cut files typeSmoothEDP no.14010Height5/16 InchLength14 InchPFERD TOOLS type299 cWidth1.375 InchPackaging unit5 EACHFile curved in longitudinal and transverse direction (convex), tanged. Cut on one side. Radial fine cut for fine stock removal and finishing. The cut is designed to achieve score-free surfaces. These tanged car body files come in industrial packaging without handles.Special featuresConvex shape of the file prevents unwanted scratches.Precise handling.Workpiece materialsSteels up to 370 HV (< 38 HRC)AluminumApplicationsDeburringLevelingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application