Shop
Bore polisher
Bore polisherThe flaps made of coated abrasive are arranged radially around the axis in a fan-type structure. Designed for fine grinding. In ISO 3919, mounted flap wheels are designated as "flap wheels with shaft."Special featuresConforms to contours due to high flexibility.Consistently high stock removal rate throughout the entire service life as new, aggressive abrasive is constantly exposed.ApplicationsCleaningDeburringStep-by-step fine grindingGrinding outLevelingRemoving oxide layersSurface workWork on weld seamsMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)AluminumBrassCast steelCopperGrey/nodular cast iron (GG/GJL, GGG/GJS)Hardened, heat-treated steels over 370 HV (38 HRC)Recommendations for useFlap wheel wear and the thermal load on the workpiece are reduced by decreasing the contact pressure and peripheral speed, and by adding grinding oil.Stock removal rate should be increased by using a coarser grit, not by increasing the contact pressure. This avoids unnecessary flap wheel wear and prevents the thermal load of the workpiece.Increasing the speed results in a slightly finer surface quality. An increase in contact pressure results in a slightly coarser surface. The softer the workpiece material, the coarser the resulting surface (when using the same grit size).For the best performance, use with a recommended peripheral speed of 3,000-4,000 SFPM. This provides an ideal compromise between stock removal rate, surface quality, thermal load on the workpiece and tool wear.Use the appropriate grinding oil for the material to significantly increase the service life and the abrasive performance of the discs.SafetyFor safety reasons, the maximum permitted rotational speed indicated must never be exceeded.The contact pressure has to be reduced significantly when the optimum rotational speed is exceeded.Technical informationDia. External5/8 inWidth3/4 inDia. shank1/4 InchDrive typeFlexible shaft driveGrit120Max. RPM31800Pack qty10
Broom Head - Fine Sweep, Horsehair/nylon mix, 79189217
Technical informationHorsehair/nylon mix, 79189217Filament MaterialHorsehair/nylon mixTrim Length3 InchPack Qty12Fine sweeping brooms for light-duty sweeping on smooth surfaces. Lacquered hardwood. High-quality sweep for best cleaning of fine dirt on smooth floors. Horsehair-nylon mix stapled into lacquered hardwood block with two threaded handle holes.AdvantagesNatural horsehair fibers minimize contamination in brazing and soldering applications.ApplicationsCleaningSweepingDrive TypesManual application
Buffing Drum, Soft Cotton Yarn
Buffing Drum, Soft Cotton YarnDue to the soft cotton yarn, ideal for high-gloss polishing with polishing pastes in tool and die-making. The ends of the threads provide optimum absorption of the polishing paste. Please order corresponding polishing pastes and arbor separately.Special featuresConforms to contours due to high flexibility.Can be freely shaped, meaning they can be used on complicated geometries.ApplicationsPolishingMaterials that can be workedStainless steel (INOX)Steel materials with a hardness > 54 HRCSteels up to 370 HV (< 38 HRC)ThermoplasticsTitaniumTitanium alloysAluminumBrassBronzeCast steelCobalt-based alloysCopperFibre-reinforced thermosetting plastics (GRP, CRP)Hardened, heat-treated steels over 370 HV (38 HRC)Nickel-based alloys (e.g. Inconell and Hastelloy)Technical informationDia. External4 inWidth4 inDrive typeDrum grindersMax. RPM3500Pack qty1
Cant saw file
Technical informationPFERD Cant Saw File 8" Three Square Second CutItem number11633202Cut2Cut files typeSecondEDP no.17014Height1/2 InchLength8 InchPFERD TOOLS type1230Width7/8 InchPackaging unit10 EACHThree square saw files from PFERD are triangular tapered tanged files. The saw files are suitable for use on steel and cast steel and especially suitable for sharpening sawing tools. PFERD offers three square saw files in various versions and shapes. Triangular file, tanged. Cut on three sides, non-equilateral triangular shape. Second cut for universal sharpening tasks. Files come in industrial packaging without handles.Special featuresGood stock removal rate.Durable.Versatile.Workpiece materialsSteels up to 370 HV (< 38 HRC)Cast steelApplicationsSharpeningCompatible power toolsManual application
Car body file blades hand
Technical informationPFERD Car Body File 14" Milled Tooth Cut 1Item number14101351Cut1EDP no.14006Height7/32 InchLength14 InchPFERD TOOLS type299 bWidth1.34375 InchVersioncoarsePackaging unit1 EACHCar body file blades in the holder can be precisely tensioned and adjusted to match the surface contour of the workpiece. Radial special coarse cut for very coarse stock removal and roughing. The cut is designed to achieve score-free surfaces. These car body files comes in industrial packaging without car body file holders. They are also individually packaged in plastic sleeves.Special featuresThe tensioning system makes it easy to adjust the bending radius of the file.Precise handling.Razor-sharp tooth edges.Convex shape of the file prevents unwanted scratches.Workpiece materialsSteels up to 370 HV (< 38 HRC)AluminumApplicationsLevelingSurface workCompatible power toolsManual application
Car body file holder
Technical informationPFERD Adjustable Holder 12" for Car Body FileItem number14000167EDP no.14012PFERD TOOLS typeKFHPackaging unit1 EACHPFERD offers holders for a range of files and file blades. The PFERD product range includes riffler file holders, adjustable holders for car body files and holders for file blades, tungsten carbide files and hand deburrers. Adjustable car body file holders allow precise tensioning of the file blade to match the workpiece surface contour. The tensioning system makes it easy to adjust the bending radius of the file to be adjusted. This ergonomic and particularly lightweight holder enables precise tensioning of car body file blades to match the workpiece surface contour.Special featuresThe tensioning system makes it easy to adjust the bending radius of the file.Particularly lightweight plastic design containing no plasticizers.Can be curved or straight, allowing it to be used on a specific spot or a wide area.Vibration-damping rubber pad reduces fatigue.Compatible power toolsManual application
Car body files tanged hand
Technical informationPFERD Car Body File 14" Cut 3 Milled Tooth with TangItem number14103353Cut3Cut files typeSmoothEDP no.14010Height5/16 InchLength14 InchPFERD TOOLS type299 cWidth1.375 InchPackaging unit5 EACHFile curved in longitudinal and transverse direction (convex), tanged. Cut on one side. Radial fine cut for fine stock removal and finishing. The cut is designed to achieve score-free surfaces. These tanged car body files come in industrial packaging without handles.Special featuresConvex shape of the file prevents unwanted scratches.Precise handling.Workpiece materialsSteels up to 370 HV (< 38 HRC)AluminumApplicationsDeburringLevelingSurface workWorking on edges (chamfering, rounding)Compatible power toolsManual application
Carbide Bur Set 12 Piece Double Cut Plastic Case
Double cut burs are cross cut and ideal for machining cast iron, steel, stainless steel (INOX), nickel-based alloys, and titanium alloys. These burs have a high stock removal rate. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. This set contains twelve small tungsten carbide burs in the shapes and dimensions most commonly used in the workshop. The sturdy plastic box protects the burs against dirt and damage.
Carbide Bur Set 12 Piece Single Cut Plastic Case
Single cut burs are ideal for machining cast iron, steel, stainless steel (INOX), nickel-based alloys, and titanium alloys. These burs have a high stock removal rate and achieve a good surface finish quality. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. This set contains twelve small tungsten carbide burs in the shapes and dimensions most commonly used in the workshop. The sturdy plastic box protects the burs against dirt and damage.
Carbide Bur Set 3 Piece MICRO Cut Plastic Case
MICRO cut tungsten carbide burs are specifically designed for finishing and are used in areas where mounted points are often used. They offer a higher stock removal rate and produce a high surface quality, particularly when compared to conventional double cut burs. MICRO cut burs also operate with low vibration and little noise, they maintain their geometry over their entire service life, and they work in both manual and machine applications. MICRO cut burs can machine almost all materials up to a hardness of 940 HV (68 HRC). This set contains three small tungsten carbide burs for finishing work in the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage.
Carbide Bur Set 8 Piece OMNI Cut Plastic Case
This set contains eight tungsten carbide burs in the shapes and dimensions most commonly used in the workshop. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has two unused slots for additional burs.
Carbide Bur Set 5 Piece ALU Cut/Non-ferrous Plastic Case
The 5-piece ALU cut bur set contains five tungsten carbide burs for processing aluminum. These burs are the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.
Carbide Bur Set 5 Piece CAST Cut Plastic Case
This set contains five tungsten carbide burs for processing cast iron. These burs are the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.
Carbide Bur Set 5 Piece Diamond Cut Plastic Case
Diamond cut burs are designed for machining stainless steel (INOX), steel, and high-temperature-resistant materials such as nickel-based and cobalt-based alloys. They have high stock removal with short chips, and achieve a good surface finish. Universal line burs are designed for fine and coarse stock removal on the key materials used in industrial manufacturing. They provide a good stock removal rate and are not specific to a particular material. This set contains five tungsten carbide burs in the shapes and dimensions most commonly used in the workshop. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.
Carbide Bur Set 5 Piece INOX Cut Plastic Case
This set contains five tungsten carbide burs for processing stainless steel (INOX). These burs are the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and. The box also has five unused slots for additional burs.
Carbide Bur Set 5 Piece STEEL Cut Plastic Case
This set contains five tungsten carbide burs for processing steel and cast steel. These burs are the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.
Carbide Bur Set 5 Piece STEEL, INOX, CAST, ALU, OMNI cuts Tree Shape
This set contains five tungsten carbide burs with different high-performance cuts for use on the most important materials such as steel, stainless steel (INOX), aluminum, and cast iron. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused slots for additional burs.
Carbide Bur Set 5 Piece TOUGH Cut/Double Cut Plastic Case
The TOUGH cut has been specially designed for tough operating conditions such as in shipyards, foundries and steel construction. It is also ideal for all demanding production environments where frequent tooth breakages and other damage to conventional burs occur. This set contains five tungsten carbide burs for tough applications in the most common shapes and dimensions. The sturdy plastic box protects the burs against dirt and damage. The burs are secured at the shanks, facilitating their selection and withdrawal. The box also has five unused holes for additional burs.
CC-GRIND grinding disc mounting flange set
ShapeSFS SOLID/FLEXPack qty1CC-GRIND®The CC-GRIND® clamping flange set optimally aligns the CC-GRIND® SOLID and CC-GRIND® FLEX in the angle grinder protective guard. This means that the grinding discs can be positioned so that they are particularly flat against the workpiece, therefore maximizing efficiency. The black backing pad is placed on the original mounting flange of the angle grinder. The silver flange nut replaces the original flange nut.
CGW | Cut-Off | Chop-Saw | Aluminum Oxide | Type 1
• A: Aluminum Oxide - Metal & Steel. 14" available in single (SR) and double (DR) fiberglass reinforced. • Fast Cut: Economical choice for metal, steel and general applications.
CGW | Cut-Off | Contaminant Free | WA - White Aluminum Oxide | Type 1
• WA: White Aluminum Oxide grain for stainless steel. • Contaminant free wheels contains 0.1% iron, sulfur, or chlorine for rust-free and corrosion-free results. • High quality grain mixture is more friable and cuts freely.
CGW | Cut-Off | High Speed Gas Saws | Aluminum Oxide | Type 1
• A24R: Aluminum Oxide - Metal & Steel, Stainless. General purpose. 14" are available in both double and triple reinforced. • A24T: Aluminum Oxide - Metal Decking & Cable. Harder bond for more cuts on thinner metals. 14" are triple reinforced. • AC: (Mix of A/C) - Used on Ductile Iron. 14" are available in both double and triple reinforced. • C16: Silicon Carbide - Asphalt/Green Concrete • C24: Silicon Carbide - Stone/Concrete
CGW | Cut-Off | Quickie Cut | Zirconia | Type 1
• ZA: Zirconia and Aluminum Oxide mixture. All purpose wheel. Zirconia grain allows for faster cutting and longer life. Excellent on Steel/Stainless. • ZA60-TB-Flex: Flexible wheel design for fast cutting and easy work penetration. • ZA-36-T-Rigid: Thicker (.045), rigid wheel design for fast cutting and longer life.
CGW | Cut-Off Blades | Stationary Saw | Aluminum Oxide | Type 1
Stationary saw cut-off wheels cut structural steel, bar stock, tubing and non-ferrous metals. • A: Aluminum Oxide - Metal & Steel. • Economical choice for metal, steel and general applications.